background image

1

Installation and Maintenance Manual, Compact CBP

Environmentally acceptable fluids

Explanation of  

 

 

 

 

"GRADE OF FILTRATION"

Grade  of  filtration 

β

10=75  indicates  the 

following:

β

10 means the size of particle 

10

µ

m that will 

be removed by filtration.
=75  means  the  grade  of  filtration  of  above 
mentioned  size  of  particle.  The  grade  of 
filtration is defined as number of particles in 
the oil before filtration in relation to number of 
particles in the oil after filtration.
Ex. Grade of filtration is 

β

10=75.

Before the filtration the oil contains 

N

 number 

of particles 

10

µ

m and after passing the filter 

once the oil contains 

 number of particles 

10

µ

m.

This  means  that 

  number  of 

particles have been filtered (=98,6%).

* Vegetable fluids give good lubrication and small change of viscosity with different temperature. Vegetable fluids  
  must be controlled every  months and temperature shall be less than +45° (11°F) C to give good service life for  
  the fluid.

** Environmental acceptabel fluid gives the same servicelife for the drive, as mineral oil.

Technical data

Filtration

The oil in a hydraulic system must always be 
filtered and also the oil from your supplier has 
to  be  filtered  when  adding  it  to  the  system. 
The grade of filtration in a hydraulic system is 
a question of service life v.s. money spent on 
filtration.
In  order  to  obtain  stated  service  life  it  is 
important  to  follow  our  recommendations 
concerning contamination level.
When  choosing  the  filter  it  is  important  to 
consider the amount of dirt particles that the 
filter can absorb and still operate satisfactory. 
For that reason we recommend a filter with an 
indicator that gives a signal when it is time to 
change the filter cartridge.

Filtering recommendations

Before  start-up,  check  that  the  system  is 
thoroughly cleaned.
1.  In  general  the  contamination  level  in  our 
motors  should  not  exceed  ISO  4406  19/15. 
(NAS 10)
.  For  heavy-duty  industrial  applications  the 
contamination  level  should  not  exceed  ISO 
4406 16/1. (NAS 7)
. When filling the tank and motor housing, we 
recommend the use of a filter with the grade 
of filtration 

β

10=75.

Fluid

Approved

Seals

Internal paint

Vegetable */** Fluid 
HTG

Yes

Nitrile (std motor)

-

Synthetic ** Esters HE

Yes

Nitrile (std motor)

-

Содержание Compact CBP 140

































Отзывы: