Kit Description TRE700 / 720
The detector and the receiver must be preset in
order to operate together.
These two products are pre-configured to operate
together. Only delay, brightness level and
detection zones are to be set by user.
Setting detector’s delay
Setting receiver’s delay
TU4xx
Kit TRE700
Pre-configured
(ON/OFF switch function)
1. Clear the previous pre-configured function
if Kit TRE700 is used (See the Configuration
Instructions)
2. Set the potentiometer to position
3. Configure the "timer"
(See the Configuration Instructions)
1 detector TRE5..
+
1 receiver
Recommended configuration :
1. Set the potentiometer to a value different
from
2. Configure ON/OFF switch function (See the
Configuration Instructions)
TU4xx
Kit TRE700
+
1 or several
other receivers
In order to have the same delay on each receiver :
1. Set the potentiometer to a value different
from
2. Configure the ON/OFF switch function (See the
Configuration Instructions) on other receivers
In order to have a different delay on each receiver :
1. Clear the previous pre-configured function if
Kit TRE700 is used (See the Configuration
Instructions)
2. Set the potentiometer to position
3. Configure the "timer" function
(See the Configuration Instructions)
1 detector TRE5..
+
several receivers
1. Set the potentiometer to a value different
from
2. Configure the ON/OFF switch function (See the
Configuration Instructions) on each receiver
TU4xx
Several detectors
TRE700-TRE5…
+
1 or several
receivers
Not recommended (conflict of delays)
1. Clear the previous pre-configured function if
Kit TRE700 is used (See the Configuration
Instructions)
2. Set the potentiometer to position on both
detectors.
3. Configure the "timer" function
(See the Configuration Instructions)
on each receiver
TU4xx
Kit TRE700/720
or
1 detector TRE5..
+
1 or several
transmitters
other than detectors
+
1 or several
receivers
Timer function being not used on the other
transmitter(s) :
1. Set the potentiometer to a value different
from
2. Configure the other transmitter(s)
(See the Configuration Instructions)
with a function other than timer
Timer function used on the other transmitters :
1. Clear the previous pre-configured function if
Kit TRE700 is used (See the Configuration
Instructions)
2. Set the potentiometer to position
3. Configure the "timer" function
(See the Configuration Instructions) on each
receiver for each transmitter involved
TROUBLESHOOTING...
P
roblem
C
auses
s
olutions
Unwanted lamp
switch on.
- Permanent heat source is active in the detection area (trees, bushes
shook by wind or presence of dogs, cats in the detection area).
- The detector is located on top a ventilation grill.
- Limit detector’s range by adjusting its inclination or by fitting shut-
tering blades to the lens, or by lowering sensitivity using the
adjustment knob.
- Move the detector to another location.
The range of
the detector is
too narrow.
- Detector’s installation height is not suitable (too high or too low).
- Sloppy ground.
- Modify installation height (2.5m is optimal).
- Adjust detector’s direction.
Moving vehicle or
person is not
detected.
- Vehicle’s motor is not enough yet (heat radiation is too weak).
- People move forwards in front of detector.
- Detector energy too low.
- Install the detector in such a way that objects move within the area
in transverse direction.
- Replace power cells.
- Place detector in a suitable location with solar cell directed towar-
ds the sun.
Technical specifications
Electrical specifications
Power Supply :
- TRE51., TRE53.
Solar
Operational characteristics
Dimensions (L x w x h) : 153 x 91 x 130 mm
Luminosity threshold : 5 —> 1000 Lux
Fixed time : 30 s —> 15 min
Sensitivity : min. 20%, max. 100%
Limiting the detection zone : Adjustable shutters supplied
Transmission frequency : 868,3 MHz
Maximum emission power : 25mW
Transmitter duty cycle : 1%
Receiver category : 2
Range : 100 m on open field
Fixing accessories : corner support
(sold separately) EE855/52125, EE856/52126
Environment
Operating temperature : -20 °C —> +55 °C
Storage temperature : -20 °C —> +60 °C
IK : 04
Protection class : IP55
Resistance to fire : 750°C
(Please refer to Detector User's Instructions).
Other devices can be added to the kit.
Various configuration options are available
When a detector is associated with a receiver, only 2
functions are available, depending on potentiometer’s
position :
-
(Red/Green LED) or timer
(Red flashing
LED) according to the case
- Delete
(LED is OFF)
The receiver will offer only the function set by the
potentiometer.
Note :
During configuration of a detector, Step 2 of the Configuration Instructions shall be ignored.
6LE003093A
3
When a product is factory reset,
pre-configuration is removed.
It should then be configured again.
