background image

CI-1255e™ Power Amplifier

Hafler

Passion for Perfection

14

# of Channels

12

Inputs

 

Gold RCA jacks with adjustable gain,

3.5mm global bus input

Optional Analog Inputs

Euroblock (Phoenix® style) connectors

Optional Digital Inputs

Dante® network connection over Ethernet

Input Impedance

22k Ohms

Outputs

Euroblock (Phoenix® style) connectors

Output Power

55 watts RMS per channel (8 Ohms) 

Peak Output Power

100 watts per channel (8 Ohms)

Bridged Output Power

120 watts per channel (8 Ohms only)

Ideal Impedance

6 - 8 Ohms

Frequency Response

+/-0.5dB from 15Hz - 50kHz

S/N Ratio

> 102dB (A weighted)

THD Distortion

< 0.1% 20Hz to 20kHz

IMD Distortion

< 0.01%@ 60Hz

Common Mode Rejection

 

-70dB direct coupled

-90dB with Jensen transformer option

Dimensions

17" x 3.5" x 11.5" (432 x 89 x 292mm)

HushTone™ Fan Noise

22dB maximum

Power (Maximum)

750 watts at 117VAC or 230VAC

Gain control

-40dB to +20dB for each channel

Weight

24lbs (11kg)

Storage Temperature

-40° to +120° C

Working Temperature

-5° to +40° C

Voltage Requirements

115V 60 Hz, 230V 50Hz

Damping Factor

400

Maximum wire gauge

10-gauge (2.59mm)

Recommended Minimum

25ft (8m) - min 18-gauge copper

Wire Gauge

 

 

 

50ft (16m) - min 16-gauge copper

100ft (32m) - min 14-gauge copper

200ft (64m) - min 12-gauge copper

500ft (160m) - min 10-gauge copper

ECOSYSTEM™ shut-off time

Automatically variable 40-200s

ECOSYSTEM™ turn-on time

10ms typical

SPeCIfICATIoNS

Specifications subject to change without notice

Содержание CI-1255e





















Отзывы: