HABCO® TECHNICAL DOCUMENT - C098791 • 10310209
© HABCO Manufacturing Inc. “HABCO, Cassette, Cold Space Merchandiser” are registered trademarks of HABCO Manufacturing Inc. Domestic and International Patents.
Page 4
HABCO® Commercial Refrigerators, Powered by Cassette®, are designed
and engineered to the highest standards using only quality components
for years of reliable service. Any use of the product for purposes other
than which it was designed, will void any and all manufacturer’s war-
ranty, stated or implied.
A. INSPECTION & UNPACKING
1. A thorough inspection of the appliance should be made prior
to formally receiving the goods from the carrier. If there are any
markings (ie. scuffs, dents, scratches) of the packaging, please note
this on the carrier’s delivery slip and have driver sign your copy
acknowledging damage. Common practice will have the carrier re-
port your concerns before leaving the premises.
2. Advise your carrier, or HABCO (if shipped via our transport) of any
damage immediately, noting the following items.
3. Retain all packaging and forward HABCO a copy of the Delivery Slip
signed by carrier acknowledging damage, Serial Number of Unit,
and digital photos of area damaged and packaging next to location
of damage.
4. Once the appliance has been received in good condition, remove
stretch-wrap, corners protectors and bag.
WARNING: RISK OF SUFFOCATION! KEEP PLASTIC PACKAGING MATERIAL
AWAY FROM CHILDREN AND ANIMALS, AND DISPOSE SAFE AND SECURE.
5. Shipping Platform Removal:
WARNING: RISK OF PERSONAL INJURY! EMPLOY BEST HEALTH AND SAFETY
LIFTING PRACTICES WHEN REMOVING SHIPPING PLATFORM(S); LEVELING
CABINET; REVERSING DOORS; AND MOVING APPLIANCE. IF IN DOUBT, ASK
FOR HELP.
Shipping Pallet - Commercial Refrigeration - FIG A1
a. HABCO® Foodservice and Commercial appliances are shipped
on pallets. Pallets are fastened with the appliance leg levelers.
Insets on each side of skid are provided to allow easy access
for 1-3/8” wrench or socket to remove the levelers and skid
respectively. Once pallet is removed, reinstall levelers and
level cabinet front to back and side to side.
FIG. A1
b. CASTER KIT INSTALLATION - OPTIONAL
HABCO® Commercial Refrigerators may be equipped with an
optional caster kit. To install caster kit, follow these proce-
dures:
i.
Install non-braking casters at rear of the refrigerator by
threading into existing leg leveler hole.
ii. Install braking casters at front of the refrigerator by threading
into existing leg leveler hole. WHEN ROLLING REFRIGERATOR
INTO POSITION, ENSURE THE FRONT CASTERS EXTEND OUT-
WARD FROM THE CABINET FACE.
iii. When in place, engage brakes on front casters.
B. LOCATION
1. Position appliance on level floor. The appliance MUST be level,
otherwise door(s) may not close and condensate may not drain
property.
2. Allow 1” (2.54 cm) clearance at rear of appliance for power cord.
WARNING: RISK OF FIRE, AND ELECTROCUTION!
DO NOT ALTER, IMPACT OR PLACE PRESSURE ON POWER CORD. AL-
LOW ADEQUATE SPACE FOR POWER CORD TO FLOAT FREELY BETWEEN
CABINET AND WALL AND DO NOT STRAIN AND/OR STRETCH POWER
CORD TO REACH ELECTRICAL RECEPTACLE.
DO NOT INSTALL OUTDOORS AND/OR IN DAMP CONDITIONS.
DO NOT INSTALL APPLIANCE WHERE STORAGE, HANDLING AND/OR DIS-
PENSING FLAMMABLE AND/OR EXPLOSIVE MATERIALS OCCUR.
3. Appliance must be positioned with front grill unobstructed.
NOTICE: RISK OF APPLIANCE DAMAGE!
DO NOT OBSTRUCT AIR-RETURN GRILLS LOCATED INSIDE CABINET NEAR
THE LOWER LEFT AND RIGHT OF THE REAR AIR DISTRIBUTION PANEL. DO
NOT BLOCK EXTERIOR, LOWER FRONT GRILL. FAILURE TO COMPLY MAY
RESULT IN RESTRICTED AIR CIRCULATION, SUBSTANTIALLY REDUCED COOL-
ING PERFORMANCE AND DAMAGE TO REFRIGERATION COMPONENTS
AND VOID WARRANTY.
DO NOT LOCATE APPLIANCE IN DIRECT SUNLIGHT OR IN CLOSE PROXIM-
ITY TO HIGH HEAT OR HIGH HUMIDITY SUCH AS FRYERS, RANGES, DISH-
WASHRS, STEAM COOKERS AND/OR HEATING DUCTS
DO NOT INSTALL DIRECTLY BENEATH UNDIFFUSED AIR CONDITION-
ING VENTS.
DO NOT INSTALL OUTDOORS, IN DIRECT SUN, DAMP, EXTREME HEAT
AND/OR COLD CONDITIONS.
C. ELECTRICAL
WARNING: RISK OF DEATH, FIRE, EXPLOSION, ELECTRICAL SHOCK AND/OR
OTHER PERSONAL INJURY!
PLUG INTO A DEDICATED, 3 PRONG GROUNDED ELECTRICAL RECEP-
TACLE AND DO NOT USE EXTENSION CORDS, POWER BARS, AND/OR
ADAPTERS TO POWER THIS APPLIANCE. IF IN DOUBT, EMPLOY A CERTI-
FIED ELECTRICIAN TO CONFIRM YOUR POWER SUPPLY MEETS CRITERIA.
DO NOT ALTER, IMPACT OR PLACE PRESSURE ON POWER CORD. AL-
LOW ADEQUATE SPACE FOR POWER CORD TO FLOAT FREELY BETWEEN
CABINET AND WALL AND DO NOT STRAIN AND/OR STRETCH POWER
CORD TO REACH ELECTRICAL RECEPTACLE.
INSPECT POWER CORD FOR ANY DAMAGE PRIOR TO POWERING AND
WHENEVER HABCO® CASSETTE® IS EXCHANGED OR APPLIANCE IS MOVED.
DO NOT PLUG THIS APPLIANCE INTO WALL RECEPTACLE IF POWER
CORD IS DAMAGED.
DO NOT ACCESS MECHANICALLY FASTENED AREAS WITHOUT PERMIS-
SION OF OWNER AND READING AND UNDERSTANDING PRODUCT
MANUAL.
DISCONNECT POWER BEFORE ACCESSING MECHANICALLY FASTENED
AREAS.
1. Check that the power supply conforms to the data plate located on
the upper left interior wall of the cabinet.
Содержание SE40eHC
Страница 2: ......
