H3C WA2620X-AGNP Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 46

H3C WA2620X-AGNP Скачать руководство пользователя страница 18

13

Installing a directional antenna on a pole

NOTE:

Ensure that the location of the pole does not hamper the adjustment of antenna direction
and tilt.

Before you install a directional antenna on the pole, make sure that the pole is vertical to the
rooftop surface.
Follow these steps to install a directional antenna:

Step1

Weld the lightning rod to the tip of the pole.

Step2

Install the pole on a parapet or cement pier.



If there are parapets on the rooftop and the height of the parapets is no less than 1.2 m (3.94
ft), you can fix the pole on a parapet with expansion screws and fix the directional antenna on
the pole with the pole mounting bracket, as shown in

Figure 9

.

Figure 9

Install a directional antenna on a parapet (I)

Lightning rod

Directional outdoor
antenna

Pole

Parapet

Pole mounting bracket

0.5 m

1.2 m

Flat steel bar

To the grounding grid



If there are parapets on the rooftop and the height of the parapets is less than 1.2 m (3.94 ft),
you can fix the pole on a parapet at one point with expansion screws and fix the bottom end
of the pole to the rooftop surface, and then fix the directional antenna on the pole with the
pole mounting bracket, as shown in

Figure 10

.

«
...
16
17
18
19
20
...
»

Содержание WA2620X-AGNP















































Отзывы:

Нет отзывов