background image

 

2

 

Installation preparations 

Unpacking and inspection 

Before unpacking the AP, ensure that the package is not damaged and that it does not 
show signs of water damage. When unpacking the contents, avoid excessive force. 
Make sure that you have the following items, which are included with the AP: 

 

One H3C WA2620-AGN Access Point  

 

Wall-mounting hardware:  

one combined wall-mounting bracket and table-top stand, four screws, four wall 
anchors, suspended ceiling bracket, one ceiling bracket, one slider, two screws 

 

Eight adhesive rubber feet 

 

One console cable 

 

Quick Start Installation Guide (this document) 

 

·One H3C Warranty 

· If the package is found to be rusted or water soaked, stop unpacking and contact 
your H3C representative immediately. 

Connection test 

H3C recommends that you connect and check the Ethernet cable and LEDs before you 
install the AP in a hard-to-reach location. Also, observe these items before you mount or 
connect the AP: 

Feature 

Description 

Switch Port 

To connect your wireless network to your 
wired network, you need a switch that is 
connected to the AP. 

Содержание WA2620-AGN






















Отзывы: