H3C SecPath F10 0 Series Скачать руководство пользователя страница 49

Страница: 49 / 68

Figure 42 Rear panel

(1) Power receptacle

(2) Interface module slot 1

(3) Interface module slot 2 (not supported)

(4) Grounding screw

F1070/F1080

The F1070/F1080 firewall provides the following ports on the front panel:

•

Sixteen 10/100/1000BASE-T autosensing Ethernet copper ports.

•

Eight 1000BASE-X fiber ports.

•

Two 10GBASE-R fiber ports.

•

Two USB ports.

•

One console port.

•

Two hard disk slots.

Figure 43 Front panel

(1) Hard disk slots

(2) LEDs

(3) 10/100/1000BASE-T copper ports

(4) 1000BASE-X fiber ports

(5) 10GBASE-R fiber ports

(6) Console port

(7) USB ports

(8) Management Ethernet port (0/MGMT)

Figure 44 Rear panel

(1) Power module slot 0

(2) Power module slot 1

(3) Interface module slot 1

(4) Interface module slot 2

(5) Grounding screw

Содержание SecPath F10 0 Series





































































Результаты поиска

Содержание SecPath F10 0 Series

Отзывы:

Похожие инструкции для SecPath F10 0 Series

Бренды по названию

Популярные бренды

H3C SecPath F10 0 Series, Руководство по установке

Результаты поиска

Содержание SecPath F10 0 Series

Отзывы:

Похожие инструкции для SecPath F10 0 Series

Бренды по названию

Популярные бренды