H3C S12500G-EF Series Скачать руководство пользователя страница 44

Страница: 44 / 97

3-17

Figure 3-18 Installing a fan tray (S12516G-EF)

(1) Pivot up the fan tray handles

(2) Insert the fan tray into the slot

(3) Fasten the captive screws

(4) Pivot down the fan tray handles

Installing power modules

The device came with one power module slot empty and the others each installed with a filler panel.

Installing a PSR1600B-12A-B power module

Remove the filler panel, if any, from the target slot. As shown in

Figure 3-19

, put your forefinger

in into the hole in the filler panel and pull out the filler panel along the guide rails.

As shown in

Figure 3-20

, orient the power module with the latch below the handle. Holding the

handle of the power module with one hand and supporting the bottom of the power module with

Содержание S12500G-EF Series


































































































Результаты поиска

Содержание S12500G-EF Series

Отзывы:

Похожие инструкции для S12500G-EF Series

Бренды по названию

Популярные бренды

H3C S12500G-EF Series, Руководство по установке

Результаты поиска

Содержание S12500G-EF Series

Отзывы:

Похожие инструкции для S12500G-EF Series

Бренды по названию

Популярные бренды