background image

 

Copyright © 2011-2012, Hangzhou H3C Technologies Co., Ltd. and its licensors 

 

All rights reserved 

No part of this manual may be reproduced or transmitted in any form or by any means without prior 

written consent of Hangzhou H3C Technologies Co., Ltd. 

Trademarks 

H3C, 

, Aolynk, 

, H

3

Care, 

, TOP G, 

, IRF, NetPilot, Neocean, NeoVTL, 

SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V

2

G, V

n

G, PSPT, 

XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co., 

Ltd. 
All other trademarks that may be mentioned in this manual are the property of their respective owners 

Notice 

The information in this document is subject to change without notice. Every effort has been made in the 
preparation of this document to ensure accuracy of the contents, but all statements, information, and 

recommendations in this document do not constitute the warranty of any kind, express or implied. 

Environmental protection 

This product has been designed to comply with the environmental protection requirements. The storage, 
use, and disposal of this product must meet the applicable national laws and regulations. 

 

Содержание S12500 Series






















Отзывы: