background image

 

11 

Examples 

# Enable the software auto-update feature.  

<Sysname> system-view 

[Sysname] irf auto-update enable 

irf domain 

Use 

irf domain

 to assign a domain ID to the IRF fabric.  

Use 

undo irf domain

 to restore the default.  

Syntax 

irf domain domain-id 

undo irf domain 

Default 

The IRF domain ID is 0. 

Views 

System view 

Predefined user roles 

network-admin 

Parameters 

domain-id

: Specifies a domain ID for the IRF fabric. The value range is 0 to 4294967295. 

Usage guidelines 

One IRF fabric forms one IRF domain. IRF uses IRF domain IDs to uniquely identify IRF fabrics and 
prevent IRF fabrics from interfering with one another.  

If one IRF fabric uses another IRF fabric as the intermediate device for LACP MAD, ARP MAD, or ND 
MAD, you must assign the two IRF fabrics different domain IDs for correct split detection. False 
detection causes IRF split. 

An IRF fabric has only one IRF domain ID. You can change the IRF domain ID by using the following 
commands: 

irf domain

mad enable

mad arp enable

, or 

mad nd enable

. The IRF domain 

IDs configured by using these commands overwrite each other.  

Examples 

# Set the IRF domain ID to 10. 

<Sysname> system-view 

[Sysname] irf domain 10 

irf link-delay 

Use 

irf link-delay

 to set a delay for the IRF ports to report a link down event.

 

Use 

undo irf link-delay

 to restore the default. 

Syntax 

irf link-delay interval 

undo irf link-delay 

Содержание MS4600 Series












































Отзывы: