H3C LSWM1FW10 Скачать руководство пользователя страница 12

Страница: 12 / 12

3-4

When removing the OAP card, note the following:

Do not touch the components on the surface of the OAP card.

Do not apply excessive force while removing the OAP card.

If you do not install a new OAP card in the slot, install a blank panel to prevent dust from entering

the switch and ensure normal ventilation in the switch.

Connecting the Management Ethernet Port Cable

Step1

Connect the management Ethernet port to the terminal.

To connect the management Ethernet port of an OAP card to the Ethernet port of a PC or router,

use a crossover cable.

To connect the management Ethernet port of an OAP card to the Ethernet port of a hub or switch,

use a straight-through cable.

Step2

After the OAP card is powered on, check the management Ethernet port status LED on the front panel

of the OAP card. If the LED is on, a link is present; if the LED is off, no link is present, and you need to

check the line.

Verifying the Installation

After the OAP card is installed, you can check the status of the LEDs on the front panel of the OAP card

to verify the operation state of the OAP card. If the OAP card works abnormally, check whether the OAP

card is correctly installed.

Содержание LSWM1FW10












