H-KING F-18 50MM EDF 4S Скачать руководство пользователя страница 10

Страница: 10 / 18

PUSHROD LINKAGES SETUP

Connect the ORX via one of the PWM/PPM/SBUS inputs of your chosen

receivers. Connect a 4S Li-Po battery pack and switch on your TX to prepare to

set the throws of the control surfaces. Ensure the servo horns on all servo

output shafts are perpendicular to servo cases, and all control surfaces are

perfectly level. Reset all electronic trims on your TX to the centre position and

remove any Dual Rates/End points settings, leave them at 100% and expo at

0%. There are two sets of pushrods which come with the kit. The shorter ones

are used for ailerons and the longer ones are used for elevators. Install the

supplied longer pushrod to the right-hand side elevator servo horn and use the

third

hole from the top as shown. Then repeat the above steps for the elevator

servo on the left-hand side. If you are happy with the above setup, you may

start to set up aileron control surfaces. Install the supplied shorter pushrod to the

right-hand side aileron servo horn and use the

forth

hole from the top as shown.

Then repeat the above steps to install the pushrod linkage on the left-hand side.

Содержание F-18 50MM EDF 4S



















Результаты поиска

Содержание F-18 50MM EDF 4S

Отзывы:

Похожие инструкции для F-18 50MM EDF 4S

Бренды по названию

Популярные бренды

H-KING F-18 50MM EDF 4S, Руководство пользователя

Результаты поиска

Содержание F-18 50MM EDF 4S

Отзывы:

Похожие инструкции для F-18 50MM EDF 4S

Бренды по названию

Популярные бренды