23
NEOCUT 105
EN
• Automatic cutting with torch AT 125
(6 m: ref. 038479, 12 m: ref. 039520):
Fine Cut
45 A
45 A
65 A
85 A
105 A
039131
039148
039155 (x 5)
039315
(x 5)
037496
039223
039162
(x 5)
039179
(x 5)
039186
(x 5)
039193
(x 5)
039445 (Ohmic)
039216
039339 (Ohmic)
039292
039308
OR
OR
• Gouging with torch MT 125
(6 m: ref. 039506, 12m: ref. 039513):
65-85 A
105 A
039223
039131
039148
039155 (x 5)
039216
039261
(x 5)
039278
(x 5)
039254
CUTTING CURRENT SETTINGS
In order to obtain the expected performance and to guarantee a long lifetime for the consumables, make sure the current is set in
accordance with the value indicated on the consumable (e.g. 45 A = 45 amps).
Adjustment is simply done using the dial on the main screen.
AIR PRESSURE ADJUSTMENT
The NEOCUT 105 is equipped with an electronicallycontrolled pressure regulator, the pressure is adjusted via the HMI (see following pages).
In order to obtain optimal performance and service life of the consumables, it is very important :
- To define the right torch length
- To use the adapted mode for the chosen consumables
- To use the appropriate current for the chosen consumables
- Leave the pressure setting on «auto».
It is recommended to check that the parameters entered on the HMI are in line with the actual configuration, especially in the case of:
- Connection point or pneumatic installation changes
- Torch length change
- Consumable type change
- Doubt.
It is possible to check the pneumatic circuit using the «air test» function, this allows, among other things, to check whether the pressure supplied
by the compressor is sufficient (see following pages).
CUTTING MODE CHOICE
Cutting / cutting with locked trigger
Use one of these two modes to perform your cutting work on solid sheet metal.
Pull the trigger to create the arc, and release it to stop or «unlock» (the arc stops by itself).
For long cuts it is possible to use the locked trigger mode, in which case the trigger can be released during cutting. This mode
prevents fatigue and keeps your hand a little further away from the cutting area.
Gouging / gouging with locked trigger
Use one of these two modes to perform your gouging work.
Pull the trigger to create the arc, and release it to stop or «unlock» (the arc stops by itself).
For long cuts it is possible to use the locked trigger mode, in which case the trigger can be released during cutting. This mode
prevents fatigue and keeps your hand a little further away from the cutting area.
Содержание 063044
