background image

    PSS-3203/2005 PROGRAMMABLE POWER SUPPLY

USER MANUAL

  12  

--Over Current Protection Setting:

Set to OCP SET window by pressing [MENU], Turn on/off the
OCP with the wheel knob and press [ENTER]. If OCP is on, when
the output current equals or exceeds the current value setting, the
output of the instrument will be off and get into over current
protection mode by displaying “OCP Error. Press “LOCAL” to
reset” on the display. Just press [LOCAL] to clear OCP status and
back to previous status.

5-3. The Display Contrast Setting

Set to Contrast Set window by pressing [MENU], modify its setting
value with the wheel knob and press [ENTER].

5-4. The Buzzer Setting

Set to Buzzer Set window by pressing [MENU], turn on or off the
buzzer with the wheel knob, then press [ENTER].

5-5.GPIB/RS232 Interface Setting

Set to Interface window by pressing [MENU]. If the GPIB is
displayed, the Address value window will be appeared, if the
RS-232 is displayed, the Baud Rate window will be appeared, then
using the wheel knob to modify the value and press [ENTER] to
complete the setting.

Note: The system will detect the interface used at present

automatically, and switch the detected interface over the
setting interface of GPIB or RS-232.

Example:

1)

 

If want to set the GPIB address value to 15:
Set to interface window by pressing [MENU], and adjust the
address value to 15 with the wheel knob and press [ENTER] to

    PSS-3203/2005 PROGRAMMABLE POWER SUPPLY

USER MANUAL

  13  

complete the setting.

2) If want to set the RS-232 Baud Rate to 9600:

Set to interface window by pressing [MENU], and adjust the
Baud Rate value to 9600 with the wheel knob and press [ENTER]
to complete the setting.

5-6. The Maximum Setting Value

MODEL

ITEM

PSS-3203

PSS-2005

Output Voltage

33.00V

21.00V

Output Current

3.100A

5.200A

Over-voltage

34.00V

22.00V

5-7.Test Lead

MODEL

ITEM

PSS-3203

PSS-2005

Current 3A

Test Lead

Current 4A-10A

Test Lead

5-8. The setting for the GPIB and RS232 Interface

If you have PSS-series programmable power supply, use the GPIB

or RS-232 interface, please refer to the PSS-series Programmer

Manual for more details.

Содержание GW-PSS-2005














Отзывы: