background image

    PSS-3203/2005 PROGRAMMABLE POWER SUPPLY

USER MANUAL

  4  

Interface

RS232 (GPIB interface option)

Power Source

AC100V, 120V, 220V

±

10%, 230V +10%/-6% 50/60Hz

Power
Consumption

PSS-2005: 215W
PSS-3203: 190W
Dimensions

110(W)

×

140(H)

×

320(D) mm.

Mechanical
Spec.

Weights

4.8 kg

Operation
Environmental

Indoor use
Altitude up to 2000 m
Ambient temperature :
    To satisfy specifications : 10

 to 35

 ( 50

°

 F to 95

°

F )

    Maximum operating ranges: 0

 to 40

( 32

°

F to 104

°

F )

Relative humidity: 85% RH(max.) non condensing
Installation Category: II
Pollution degree: 2

Storage
Temperature &
Humidity

-10

°

 to 70

, 70%RH (maximum)

Accessories

Power cord….............……….. 

×

  1

Instruction manual……………..

×

  1

Programmer manual................. 

×

  1

Test Lead……….………………

×

  1

    PSS-3203/2005 PROGRAMMABLE POWER SUPPLY

USER MANUAL

  5  

3.PRECAUTIONS BEFORE OPERATION

3-1.Unpacking the Instrument

The product has been fully inspected and tested before shipping from the

factory. Upon receiving the instrument, please unpack and inspect it to

check if there is any damage caused during transportation. If any sign of

damage is found, notify the bearer and/or the dealer immediately.

3-2.Checking the Line Voltage

The product can be applied by any kind of line voltages shown in the table

below. Before connecting the power plug to an AC line outlet, make sure

the voltage selector of the rear panel is set to the correct position

corresponding to the line voltage. It might be damaged the instrument by

connecting to the wrong AC line voltage.

WARNING.  To avoid electrical shock the power cord

protective grounding conductor must be connected to

ground.

AVERISS: Pour éviter les chocs électriques, le fil de terre

du cordon secteur doit impérativement être relié à la

terre.

When line voltages are changed, replace the required fuses shown as below:

Model

Line

voltage

Range

Fuse

Line

voltage

Range

Fuse

PSS-3203

PSS-2005

100V
120V

90-110V

108-132V

T3A

250V

220V
230V

198-242V
216-250V

T1.6A

250V

Содержание GW-PSS-2005














Отзывы: