GUSMER GAP Pro Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 26

GUSMER GAP Pro Скачать руководство пользователя страница 2

GAP Pro Spray Gun

2

36943-1, Issue 1

NOTICE:

The equipment described in this technical manual must only be operated or serviced by properly trained

individuals, thoroughly familiar with the operating instructions and limitations of the equipment. For technical service, call
your local distributor. Call: 1-800-FOR-GSMR (1-800-367-4767) for the name and telephone number of your local
distributor.

NOTICE:

All statements, information and data given herein are believed to be accurate and reliable but are presented

without guarantee, warranty or responsibility of any kind expressed or implied. Statements or suggestions concerning
possible use of GUSMER equipment are made without representation or warranty that any such use is free of patent
infringement, and are not recommendations to infringe

any patent. The user should not assume that all safety measures are

indicated or that other measures may not be required for a particular circumstance or application.

«
1
2
3
4
...
»

Содержание GAP Pro



























Отзывы:

Нет отзывов