Güralp DM24 MkIII Скачать руководство пользователя страница 89

Страница: 89 / 130

Güralp DM24 Mk

Ⅲ

Command line interface

Instructs the DM24 to transmit all the data streams it holds next time a

DOWNLOAD

issued. This command does not alter the read point or time period; you should either
specify a time period or use the

ALL-FLASH

command in addition to this one.

6.12.4 STREAM

Syntax:

STREAM

stream-id

(

n.b. - trailing parameter

)

Instructs the DM24 to transmit only the stream with ID

stream-id

. Stream IDs are

normally a 4-character Serial n

followed by a component letter and a tap number.

Note:

Unlike most FORTH commands, the stream-id parameter goes after

the command.

6.12.5 STATUS-ONLY

Syntax:

STATUS-ONLY

Instructs the DM24 to transmit only status streams (text streams, normally with
stream IDs ending in

6.12.6 S/S

Syntax:

rate

S/S

Instructs the DM24 to transmit only streams with sample rates equal to

rate

. If

rate

is zero, only status streams are transmitted.

Note:

This command should not be confused with the SAMPLES/SEC

command.

6.12.7 ALL-TIMES

Syntax:

ALL-TIMES

Clears any time selection in force, allowing you to download all data held by the
DM24. This command does not alter which streams are to be transmitted; you
should specify streams or use the

ALL-DATA

command in addition to this one.

6.12.8 FROM-TIME

Syntax:

yyyy

FROM-TIME

Instructs the DM24 to transmit only data more recent than the time specified by

yyyy

mm-dd

, where:

•

yyyy

is a four-digit year (1989 – 2069);

MAN-D24-0004

Issue U - December, 2021

Содержание DM24 MkIII



































































































































Результаты поиска

Содержание DM24 MkIII

Отзывы:

Похожие инструкции для DM24 MkIII

Бренды по названию

Популярные бренды

Güralp DM24 MkIII, Руководство оператора

Результаты поиска

Содержание DM24 MkIII

Отзывы:

Похожие инструкции для DM24 MkIII

Бренды по названию

Популярные бренды