Guilin Woodpecker Medical Instrument AP-A Скачать руководство пользователя страница 11

Страница: 11 / 26

There is air flow but

no water spray.

Unconnected air source

or low air pressure (≤

3bar).

Check the air connection

and ensure that the

pressure meets the

requirements of the

device (5bar-7bar).

Handpiece blocked.

Use nozzle to dredge

handpiece.

Tail line blocked.

Contact local distributors

or manufacturer.

The internal pipeline

of the main unit is

blocked.

Contact local distributors

or manufacturer.

Solenoid valve failure. Contact local distributors

or manufacturer.

There is air spray

but no water.

Solenoid valve

failure.

Contact local

distributors or

manufacturer.

Solenoid Valve

blocked due to

impurities.

Open the main unit

dredge solenoid

valve or contact

local distributors or

manufacturer.

There is no air and

water spray.

Abnormal foot

switch connection.

Reconnect foot

switch.

Foot failure.

Repair or replace foot

switch.

Powder tank

leakage

Seal ring damaged.

Replace seal ring.

Airpolishing

handpiece leakage.

Tail line seal ring

damaged, deformed

or missing.

Replace seal ring.

Handpiece plug

difficult.

Handpiece snap ring

deformation

Replace snap ring.

Note: If the fault cannot be removed, please contact your local

distributor or manufacturer.

4 Cleaning, Disinfection and Sterilization

Содержание AP-A



























Результаты поиска

Содержание AP-A

Отзывы:

Бренды по названию

Популярные бренды

Guilin Woodpecker Medical Instrument AP-A, Инструкция по эксплуатации

Результаты поиска

Содержание AP-A

Отзывы:

Бренды по названию

Популярные бренды