•
A maximum recharge time of 10 hours should
not be exceeded.
•
Check the battery if charging an empty battery is
completed in just 1 minute. The battery could be
significantly discharged, which means it cannot be
charged any more with this charger.
Start-up Assistance
for vehicles with 35-105 AH lead-acid batteries 12V
•
Battery charger, as in the manual of the connected
vehicle.
•
Battery charger connected to the power supply, switching
and charging choose (12 V/24 V).
•
Compress the „Boost“ button and wait for the time on the
timers displayed to expire in ca 2 min.)
•
When the time of the times expire, a sign of AUU will
appear on the display, and the LED to assist at starting
will light up .
•
The charger is for the startup process ready.
•
On principle, two persons should always start up a
vehicle with chargers.
•
The first person shall push the Start button on the charger
The other one shall immediately start the ignition, max. 9-
10 sec.
•
As the vehicle starts up, stop starting immediately
•
If the attempt to start fails, wait about 5 minutes for the
charger to get cooled and only then begin another
attempt to start.
Caution:
The V520 battery charger e has a safety device
fitted to protect the instrument board electronics in the vehicle !
Æ
Should the starting assistance be not in operation for the
first time, the battery has to be pre-charged unplugged for ca
20 minutes! (charging current of ca 20% of the battery
capacity)
Tip: If you change the battery for 10-15 minutes to
subpoena requires much less battery power startup.
Warning: The fuses may burn through and the
vehicle damaged if the starting time is more than 10 s.
Note: The terminals may not touch.
Notice: The charger is equipped with overload
protection.
Operator Safety Instructions
•
Any safety and protection devices must be fitted in place
before switching the unit on.
•
It is forbidden to attempt starting vehicles, the batteries of
which are discharged or damaged as that would result in
damaging the unit.
•
Any attempts to start in position “charging” instead of
“starting” could damage the ammeter and start the
overload protection.
•
Before pressing the main switch, make sure that the unit is
connected correctly.
•
Warning! If in doubt, consult a specialist in an authorized
servicing center.
•
Do not use the unit until you have read the manual
carefully.
•
Observe all the safety regulation in this manual.
•
Be responsible to the others.
Step-by-step Instruction
Charging
1.
Connect the charger .
2.
Plug in .
3.
Switch the charger on 12V / 24 V
4.
Select the charging current
Starting
1.
Connect the charger .
2.
Connect to the mains
ě
.
3.
Switch the charger on 12 V/ 24V
4. Press
“Boost“
5.
Wait until “AUU“ is displayed
6.
Start the vehicle
7.
Stop immediately the starting process and switch off and
disconnect the charger as soon as the engine starts.
Troubles-Causes-Troubleshooting
Overload circuit-breaker:
1.
Connect the red clamp to the positive pole and the black
one to the negative pole.
2.
Remove the contact and check the fuses.
3.
Set the charger at the lowest charging degree. .
Overload Causes
1.
Mixing up the poles when connecting the clamp to the
battery
2.
The battery is heavily or completely discharged.
3.
Battery is completely discharged and its capacity is higher
than the charger power
4.
Battery is damaged or defective (internal elements short
circuit).
Inspections and Maintenance
•
Unplug before any work on the unit.
•
Use a wet cloth to clean the plastic parts. Do not use
detergents, solvents and sharp articles.
•
Use a soft brush or a paint brush to remove the settled
dust from the vent and moving parts.
Inspections and Maintenance Safety Instructions
After every use
Clean the vents and moving parts from dust
Regularly
Check all the screws to see if they are tight.
11
Содержание Velox 520
Страница 2: ...1 ...