Gude GSB 20/12 Скачать руководство пользователя страница 6

Страница: 6 / 17

Fig. 1

7. Assembling

Assembling and Cleaning

Carefully unpack the drill and all the parts and compare against the list below. Do not throw away the carton

and wrapping until the drill press is completely assembled.
Any worked surface is treated with protective coating to protect the machine against moisture. Remove the

coating using a soft cloth wetted with kerosene or WD-40 agent. Never use acetone. petrol or solvents for

CLEANING.

Parts Fig. 1

1 - Motor assembly

10 - Stems/advancement lever

2 - Column

11 - Column lock lever

3 - Service instruction (manual)

12 - Top knob

4 - Tapered drift

13 - 2 hex-wrenches & cotter

5 - Bench crank

6 - Screws/bolts

7 - Chuck and chuck key

8 - Bench

9 - Base plate

Warning:

If a part is missing or found damaged. do not connect the drill to the voltage source until the missing

or defective part is replaced and the assembly completed.

Assembly tooling:

- Monkey wrench

- Screwdriver*

- Hammer and a piece of wood

Fig. 2

Содержание GSB 20/12


















Результаты поиска

Содержание GSB 20/12

Отзывы:

Похожие инструкции для GSB 20/12

Бренды по названию

Популярные бренды

Gude GSB 20/12, Руководство пользователя

Результаты поиска

Содержание GSB 20/12

Отзывы:

Похожие инструкции для GSB 20/12

Бренды по названию

Популярные бренды