25
GB
ENGLISH
absorption system and wear a suitable dust protection
mask. Remove deposited dust thoroughly, e.g. with a
vacuum cleaner.
The machine must be set during operation on a
horizontal, flat surface or be mounted with vibration
because working when sharpening with water (eg one
workbench).
Switch the machine off and unplug it when unattended.
Check all screw and plug-in connections and
protective equipment if firm and tightened
properly and whether all moving parts are
running smooth whenever the appliance is to be
put into operation.
The protective equipment on the appliance is
strictly prohibited to be disassembled, changed,
used in conflict with the designation and it is
prohibited to attach any protective equipment of
other manufacturers.
The appliance must not be used if damaged
or safety equipment is defective. Replace any
worn-out and damaged parts.
Any defect on the power tool, including on the protective
equipment or abrasive wheel must be reported to a safety
engineer immediately after it is identified.
Before use check machine, cable, and plug for any dama-
ges or material fatigue. Repairs should only be carried out
by authorised Service Agents.
Make sure the abrasive wheel is fitted properly before
pressing the O Off button.
To make sure the work is safe, use equipment such as
power tool supports, magnifying glass, workpiece holder,
etc.
Removing sawdust and chippings from the machine
when running is strictly prohibited.
Choose the abrasive wheel suitable for the given work-
piece.
Abrasive wheels not corresponding to the characteristics
given in these Operating Instructions may not be used.
The maximum revolutions given on the abrasive wheel
must be respected.
Familiarise with the safety procedures for cleaning,
maintenance and regular removal of sawdust and dust to
reduce the risk of fire.
Make sure the flange used is suitable for the given purpo-
se of use, as specified by the manufacturer.
The power tool must immediately be switched off if it
gets blocked. Unplug the power tool and remove the
stuck workpiece.
At frequent intervals, check the adjustment of the
protection against sparks and set the abrasive wheel
wear properly. Keep the distance between the protection
against sparks and the abrasive wheel small if possible
(max. 2 mm).
At regular intervals, check the workpiece support adjust-
ment and set the abrasive wheel wear properly.
Do not grind with a cold abrasive wheel. Let the abrasive
wheel run idle for one minute before starting your work.
Do not grind on the side surfaces of the wheel. Grind on
the front side only.
Do not apply the coolant directly on the abrasive
wheel.
The coolant may affect the adhesion of the abra-
sive wheel and cause its failure.
Abrasive wheel to be levelled on the front side only.
High temperatures are present when grinding.
Do
not touch the workpiece before it has sufficiently cooled
down.
IMPORTANT NOTICE
The engine is automatically switched off when overloa-
ded. The engine can be switched on again after it has
cooled down (various times).
Hold the workpieces firmly using the holder (e.g. by pliers)
to prevent injuries.
IMPORTANT NOTICE
When using the wet grinding disc please note
that the
water is drained after use by using the bleed nipple from
the container, otherwise soak the wheel with water and if
it is given dissolves or unbalanced.
Maintenance
Before carrying out any work on the machine,
disconnect the plug from the socket.
WARNING
The machine must not be used under any
circumstances if the machine or the safety devices are
damaged.
Repairs and works specified in these Instructions may
only be performed by qualified authorised staff.
At all times, keep the machine, ventilation slots, in
particular, clean. The sawdust ejection and/or dust ex-
hauster should be cleaned at regular intervals. Never
spray water on the machine!
Use only original accessories and original spare parts.
Only a regularly maintained and treated appliance
can serve as a satisfactory aid. Insufficient mainte-
nance and care can lead to unforeseen accidents and
injuries.
Never clean the machine and its components with
solvents, flammable or toxic liquids. Us only a damp
cloth making.
Apply environment-friendly oil to all moving parts.
If necessary, a list of spare parts can be found at www.
guede.com.
