GÜDE Expert PDU Energy 8311 Series Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 81

background image

77

Expert PDU Energy 8311

© 2021 GUDE Systems GmbH

Support

WEEE-number: DE 58173350
Value added tax identification number (VAT): DE 122778228

5.3

Declaration of Conformity

This product from the

Expert PDU Energy 8311

series is in conformity with the

European directives for CE marking applicable to this product. The complete CE de-
claration of conformity for this product can be found on the website www.gude.info in
the download section of the product.

5.4

FAQ

1. What can I do if the device is no longer accessible?

·

If the Status LED is red, the device has no connection to the switch. Unplug and plug
the Ethernet cable. If the Status LED is still red, try other switches. If one uses no
switch, but connects e.g. a laptop directly to the device, make sure you are using a
crossover Ethernet cable.

·

If the status LED is orange for a longer time after unplugging and plugging the Ether-
net cable, then DHCP is configured, but no DHCP server was found in the network.
After a timeout, the last IP address is configured manually.

·

If there is a physical link (status LED is green) to the device, but you can not access
the web server, bring the device into bootloader mode and search for it with
GBL_Conf.exe

. Then check the TCP-IP parameters and change them if neces-

sary.

·

If the device is not found by GBL_Conf.exe in bootloader mode, you can reset the
settings to factory defaults

as the last option.

2. What can be done if the device is no longer accessible, but the buttons still re-
spond?

·

Entering or leaving the bootloader mode does not change the state of the relays. In
the chapter Maintenance

there is a description how to activate the bootloader by

pressing the buttons and how to exit the bootloader afterwards. This will restart the
firmware without switching relays. However, this procedure does not help if the net-
work itself is incorrectly configured.

3. Where is the serial number stored in the device?

The serial number is not stored in the device, but only visible on the device label.
However, you can display the MAC address in the IP address configuration

. If you

contact Gude Systems Support with the MAC address, we will be happy to give you the
corresponding serial number.

4. Why does it sometimes take so long to configure new SNMPv3 passwords on
the website?

The authentication methods "SHA-384" and "SHA-512" are calculated purely in soft-
ware, and can not use the crypto hardware. On the configuration page, e.g. "SHA-512",
needs up to 45 seconds to calculate the key.

14

20

19

23

«
...
75
76
77
78
79
...
»

Содержание Expert PDU Energy 8311 Series


















































































Отзывы:

Нет отзывов

Похожие инструкции для Expert PDU Energy 8311 Series

Бренд: YIHUA Страницы: 2

Бренд: Valex Страницы: 8

Бренд: Velleman Страницы: 9

Acute NT Series

Бренд: Amada Страницы: 7

STORMFORCE SFAR12

Бренд: Draper Страницы: 22

Бренд: Whelen Engineering Company Страницы: 4

Бренд: Gallagher Страницы: 76

Power Xpert Series

Бренд: Eaton Страницы: 156

Portable AC-to-DC Regulated Power Supply

Бренд: Radio Shack Страницы: 28

Бренд: Wacker Neuson Страницы: 112

Бренд: Laguna Tools Страницы: 9

Бренд: Senco Страницы: 46

Бренд: Grizzly Страницы: 2

Бренд: Lutool Страницы: 21

Бренд: Meec Страницы: 24

Бренд: FROGBRO Страницы: 8

GALAXY EVO EGX850EWT

Бренд: ENERMAX Страницы: 60

Бренд: NovoPress Страницы: 214

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды