16
GB
ENGLISH
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
d)
Remove any adjusting key or wrench before turning
the power tool on.
A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
e)
Do not overreach. Keep proper footing and balance
at all times.
This enables better control of the power
tool in unexpected situations.
f)
Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
moving parts.
Loose clothes, jewellery or long hair
can be caught in moving parts.
g)
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used.
Use of dust collection
can reduce dust-related hazards.
4) Power tool use and care
a)
Do not force the power tool. Use the correct power
tool for your application.
The correct power tool will
do the job better and safer at the rate for which it was
designed.
b)
Do not use the power tool if the switch does not turn
it on and off.
Any power tool that cannot be control-
led with the switch is dangerous and must be repaired.
c)
Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories, or
storing power tools.
Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d)
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e)
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s ope-
ration. If damaged, have the power tool repaired
before use.
Many accidents are caused by poorly
maintained power tools.
f)
Keep cutting tools sharp and clean.
Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g)
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed.
Use of the power tool for operations
different from those intended could result in a hazar-
dous situation.
5) Service
a)
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
Safety instructions Stabschleifer
Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30ma).
The machine must be plugged to 230 V with 16
A fuse.
wear protective glasses
waRNING
The dust produced when using this tool may
be harmful to health. Do not inhale the dust. Use a dust
absorption system and wear a suitable dust protection
mask. Remove deposited dust thoroughly, e.g. with a
vacuum cleaner.
Switch the machine off and unplug it when unattended.
Check all screw and plug-in connections and
protective equipment if firm and tightened
properly and whether all moving parts are
running smooth whenever the appliance is to be
put into operation.
The protective equipment on the appliance is
strictly prohibited to be disassembled, changed,
used in conflict with the designation and it is
prohibited to attach any protective equipment of
other manufacturers.
The appliance must not be used if damaged
or safety equipment is defective. Replace any
worn-out and damaged parts.
Any defect on the power tool, including on the protective
equipment or abrasive wheel must be reported to a safety
engineer immediately after it is identified.
before use check machine, cable, and plug for any dama-
ges or material fatigue. Repairs should only be carried out
by authorised Service Agents.
Make sure the abrasive wheel is fitted properly before
pressing the O Off button.
To make sure the work is safe, use equipment such as
power tool supports, magnifying glass, workpiece holder,
etc.
Removing sawdust and chippings from the machine
when running is strictly prohibited.
Choose the abrasive wheel suitable for the given work-
piece.
