background image

Note: This is a control system which must be cleaned and maintained regularly (see Maintenance Guide and Record card included with valve shipment).

5

Guardian Equipment 
1140 N North Branch St 
Chicago, IL 60642

312 447 8100 

telephone

 

312 447 8101 

facsimile 

gesafety.com

rev. 1215 / © 2015  Guardian Equipment

Installation, Operation and Maintenance Guide

G3600LF Series Thermostatic Mixing Valves

11

12

13

15

14

16

RK3600B

 

Repair Kit*

RK3600A

 

Repair Kit

Notes:

1. After installing new parts, the adjustable high 

temperature limit stop must be reset (see page 2).

2. G3600LF valves are furnished with lockable dials.

* Includes parts to repair both hot and cold checkstops

Set Screw

Thermostatic Mixing Valve Parts

Item Part Number

Description

1

TA-5

Base Stud

2

MU-2C

Cover Screw

3

6810

Thermostat Group

4

6820

Stop

5

68240

Handle

6

MU-5A

Stem O-Ring

7

3009

Cover O-Ring

8

TAG-1M

Port Sleeve Assembly

Item Part Number

Description

9

6806

Cover Gasket

10

3402

Port Sleeve Nut

11

LVC-8A

Check Bonnet Packing

12

MU-6A

Lower Stem with Packing

13

MU-9A

Check Spring

14

MU-5A

O-Ring

15

MU-4A

Upper Check Stem

16

192700

Check Bonnet

1

9

7

8

10

2

4

5

3

6

7

6

9

10

8

Checkstop Parts

Thermostat Group

Lockable Dial

Содержание G3600LF Series







Отзывы: