background image

Installation and Use

 G

uar

di

an

 F

al

l P

ro

te

ct

io

 63

05

 S

. 2

31

st 

St

., 

Ken

t, 

W

A

 9

80

32 

 

4

Part # 00125: Maximum flange width: 8” - 18“. Maximum flange thickness: 2.5”.
Part # 00127: Maximum flange width: 8” - 18“. Maximum flange thickness: 2.5” - 4”.
Part # 00130: Maximum flange width: 12” - 24“. Maximum flange thickness: 2.5”.
Part # 00135: Maximum flange width: 12” - 24“. Maximum flange thickness: 2.5” - 4”.

Prior to installation, plan your system:

1. The Beamer BBC is an adjustable anchorage connector, and is designed for use either overhead or at foot
level. If used below the harness dorsal D-ring in fall arrest applications, ALWAYS account for increase in
required fall clearance, and ALWAYS use PFAS equipment explicitly certified for extended free fall up to 12’.

2. Ensure that all PFAS equipment to be used in combination with Beamer BBC Anchors is selected and
deemed compatible by a Competent Person. Make considerations for eliminating or minimizing swing fall
hazards.

3. Ensure selected “I” or ”H” structural beam is capable of supporting minimum load of 5,000 lbs., is
compatible with applicable Beamer Anchor, and adheres to the flange thickness and width requirements
specified by this instruction manual. For installation onto horizontal beams only. Never install on vertical
beams. If unable to determine suitable installation location, consult jobsite Competent Person. The Beamer
BBC is rated for loading in any direction provided it is installed as prescribed.

4. Beamer Anchor MUST NOT be used as a permanent anchorage connector, or as a component of a horizontal
lifeline system.

Installation and Use:

1. Hook Fixed Clamp over selected beam flange. Aluminum Bar MUST be positioned perpendicular to beam.

2. Position Adjustable Clamp as
tightly as possible against opposite
side of beam flange. Beamer BBC
Anchor MUST be snug against beam
flange and no possibility may exist
for Beamer BBC Anchor to detach
from beam flange.

3. Insert Locking Pin into closest
possible hole on Aluminum Bar and
ensure Beamer BBC Anchor is fully
locked in place.

4. Attach complete and compatible
PFAS to Beamer BBC Anchor
Connection Point. Extended free fall
connecting device must be used if
Beamer Anchor is located below
harness dorsal D-ring.

Beamer BBC Anchor MUST be installed so no

risk exists for it to come off end of beam.

Beam MUST possess physical

barrier that functions to eliminate

all risk of disengagement.

!

WARNING

Содержание 00101

























Отзывы: