manualshive.com logo in svg

GTO SW-2002XL, Руководство по установке, Страница: 14 / 44

Поделиться
Скачать
GTO SW-2002XL Скачать руководство пользователя страница 14

0

DRIVE

•  Low friction screw drive (linear actuator) rated for -5 ºF to +60 ºF (-2 ºC to +7 ºC). 

•  Powered by a 2 V motor with integral case hardened steel gear reducer.  Motor speed reduced to 260 rpm. 

•  Maximum opening arc of 0º.  Approximate opening time (90º): From 5 seconds, depending on weight of gate.

•  Generates 330 ft lbs of torque at 2v.

POWER

•  The system is powered by a 2 Vdc, 7.0 Ah, sealed, rechargeable acid battery. 

•  Battery charge is maintained by a 20 Vac, 8 Vac output transformer rectified to 4.5 Vdc (40 VA) through the GTO 

control board.  One () blade-style control board fuse rated for 5 A.

   

NOTE: The transformer should not be 

directly 

connected to any battery.  Do not replace fuses    

 

 

with higher ampere rated fuses; doing so will void your warranty and may damage your control board.   

•  Battery charge is maintained by

 

GTO Solar Panel Charger:  float voltage of 4.5 Vdc output from solar panel.  A gated 

diode on the control board prevents battery discharge.

CONTROL

•

  GTO

 microprocessor-based control board is set for pull-to-open gate installations.  DIP switches can be adjusted to 

accommodate an optional kit for push-to-open gates (

see Accessory Catalog

).

•  Control board has temperature compensated circuits.

•  A circuit on the control board regulates charging.  "Sleep draw" is 5 mA; "active draw" is 2 to 5 A.

•  Auto-memorization of digital transmitter code.  

•

  

GTO remote-mounted RF receiver tuned to 38 MHz. 

•  Operator length with push-pull tube fully retracted is 33

¾

", mounting point to mounting point. Max stroke is 3".

•  Adjustable auto-close timer and obstruction sensitivity.

•  Power terminal bock accommodates a transformer or solar panels.

•  DIP switches simplify setup of gate opener.

•  Accessory terminal lock is fully compatible with push button controls, digital keypads, safety loops, etc.

•  Control board allows connection of safety edge sensors and photoelectric sensors.

•  Audio entrapment alarm sounds if the unit encounters an obstruction twice while opening or closing.

OPERATIONAL CAPACITY

•  The Gate Capacity Chart shows approximate cycles, per day, you can expect from the GTO/PRO® 2002XL Auto-

matic Gate Operator when powered with a transformer. Actual cycles may vary slightly depending upon the type and 

condition of gate and installation.

GTO/PRO® 2002XL  AUTOMATIC GATE OPERATOR

Technical Specifications  

These specifications are subject to change without notice.

IMPORTANT: BALL BEAR-

ING HINGES SHOULD 

BE USED ON ALL GATES 

WEIGHING OVER 250 Lbs.

NOTE:

 "NR" indicates this 

size and weight combination 

is not recommended for the 

GTO/PRO 2002XL.

To determine the number of cycles the gate opener will perform using solar panels, please see the specifications 

listed on 

page 21

 or call

 (800) 543-1236

 or 

(850) 575-4144

 for more information.

* An operation cycle is one full opening and closing of the gate.

Number of Cycles Per Day

GTO/PRO 2002XL Gate Capacity /Cycle Chart 

Estimated number of daily cycles, based on use with a transformer and one(1) 12 Volt battery.

Gate W

eight

Gate Length

400 lbs.
300 lbs.
200 lbs.
150 lbs.
100 lbs.

50 lbs.

73
78
83
88
93

5’ - 6’

68

63

58

53

68
73
78
83
88

8’

63
68
73
78
83

10’

58
63
68
73
78

12’

Содержание SW-2002XL













































Отзывы:

Нет отзывов