manualshive.com logo in svg

GTO /PRO SW-510, Руководство по установке

Поделиться
Скачать
GTO /PRO SW-510 Скачать руководство пользователя страница 18

15

ADJUSTING THE LIMIT SWITCHES

Test the operator to verify
that the limit switches are
properly set.  The operator
should open and close the
gate completely.  After
properly setting the limit
switches, the control board
must be set according to the
operator application.  The
system accessories should
also be connected to the
control board.

The limit switches determine how far the gate travels to open and close.  The closer the limit nut is to the limit switch,
the less distance the gate will travel to open or close.  Adjust the limit switches by
moving the limit nuts.

MAKE SURE THE OPERATOR POWER IS OFF BEFORE ATTEMPTING TO
ADJUST THE LIMIT SWITCHES.

Lift and release the limit switch plate to unlock the limit nuts (see illustration at
right).  Using a fingertip, roll the limit nuts  along the travel shaft until the correct
open and closed gate positions are determined.

If the operator is mounted to the LEFT of the gate (see illustration below):
the left limit switch adjusts the open position.  The right limit switch adjusts
the closed position.

If the operator is mounted to the RIGHT of the gate (see illustration below):
the  right limit switch adjusts the open position.  The left limit switch adjusts
the closed position.

Lift limit switch plate to release,

       then adjust limit nut.

Limit Adjustment Lock

Limit Switch
    Plate 

Right Limit Nut

CLOSED position stop –

if gate opens LEFT to RIGHT

OPEN position stop –

if gate opens RIGHT to LEFT

Left Limit Nut

OPEN position stop –

if gate opens LEFT to RIGHT

CLOSED position stop –

if gate opens RIGHT to LEFT

The closer the limit nut is to the limit switch,

the less distance the gate will travel to

open or close. 

Limit Switch

Limit Switch

Limit Switch

    Plate

Travel Shaft

–

+

NEG

POS

–

+

NEG

POS

NEGATIVE LEAD from control box

to NEGATIVE Battery Terminal

POSITIVE LEAD from control box

to POSITIVE Battery Terminal

JUMPER

POSITIVE TO NEGATIVE

Battery Terminals

Connecting Back-Up Batteries

Connect the Positive Lead from the control board to the
Positive Terminal on the first battery and the Negative
Lead from the control board to the Negative Terminal on
the second battery.

Now place a Jumper Lead from the Positive Terminal on
the first battery to the Negative Terminal on the second
battery.

Содержание /PRO SW-510


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды