manualshive.com logo in svg

GTO /PRO SW-510, Руководство по установке

Поделиться
Скачать
GTO /PRO SW-510 Скачать руководство пользователя страница 11

8

TECHNICAL SPECIFICATIONS

for the GTO/PRO SW-5101 & SW-6101 AC Swing Gate Operators

Motor

•GTO/PRO SW-5101

:  1

/

2

 hp GTO-Leeson 1625 rpm TEFC; C-Face connection; 115 V, three phase.

•GTO/PRO SW-6101:    1 hp GTO-Leeson 1600 rpm TEFC; C-Face connection; 115 V, three phase.

Gear Reducer
•Totally enclosed 900:1, double reduction gear reducer, with vertical motor flange.
•Machine cut bronze gears run in an oil bath.
•Oil temperature range: –22 

°

F to 806 

°

F (–30 

°

C to 430 

°

C).

Power
•GTO/PRO SW-5101: 115 Vac, 60 Hz, 5 A; GTO/PRO SW-6101: 115 Vac, 60 Hz, 9.8 A.
•Requires copper conductors.
•Must be installed by an electrician in accordance to NEC (National Electric Code) and local codes.
•Product relies on a 15 A main disconnect circuit breaker (supplied by the installer).
•One 115 Vac dual GFCI outlet (located below control box) for additional accessories.
•Two 12 V back-up batteries provide up to 50 gate cycles in the event of a power failure

Control
•Adjustable auto-close timer: 1 – 120 seconds.
•Independent obstruction settings for opening and closing cycles.
•Diagnostic and error condition LEDs.
•Potentiometers and DIP switches for easy adjustments.
•Six separate terminals for N/O contacts (e.g., safety edges or photoelectric beams).
•Mechanical limit controls.
•GTO remote mounted RF receiver tuned to 318 MHz (other receivers can be accommodated).
•Inverter provides soft start/soft stop gate movement and control battery back-up feature.

Construction
•Zinc plated steel parts for maximum corrosion resistance.
•Mounting brackets can be welded or bolted.
•Lockable foot pedal release (patented) allows manual operation of gate.

Operational Capacity
•Operator compatible with all types of horizontal swing gates / with a maximum opening of 90 degrees
•GTO/PRO SW-5101: maximum weight 1500 lb.; maximum length 20 ft.
•GTO/PRO SW-6101: maximum weight 2500 lb.; maximum length 20 ft.
•Duty Cycle: Continuous.

Dimensions
•Housing: Width 24 in.; Depth 25.5 in.; Height 29.5 in.
•Control Box: Width 14 in.; Depth 6 in.; Height 16 in.
•Shipping Weight: GTO/PRO SW-5101 321 lb.; GTO/PRO SW-6101 327 lb.

Содержание /PRO SW-510


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды