background image

©

2007 GTO, Inc.

R4000XL INST

     

re

v - 09/13/07

WARNING!

This equipment is similar to other gate or door equipment and meets or exceeds 

Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has 

hazards associated with its use and therefore by installing this product the installer 

and user accept full responsibility for following and noting the installation and 

safety instructions. Failure to follow installation and safety instructions can result 

in hazards developing due to improper assembly. You agree to properly install this 

product and that if you fail to do so GTO, Inc. shall in no event be liable for direct, 

indirect, incidental, special or consequential damages or loss of profits whether 

based in contract tort or any other legal theory during the course of the warranty 

or at any time thereafter. The installer and/or user agree to assume responsibility 

for all liability and use of this product releasing GTO, Inc. from any and all 

liability.  If you are not in agreement with this disclaimer or do not feel capable 

of properly following all installation and safety instructions you may return this 

product for full replacement value.

READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before 

attempting to install and use this automatic gate operator.  This gate operator 

produces a high level of force.  Stay clear of the unit while it is operating and 

exercise caution at all times.

All automatic gate operators are intended for use on vehicular gates only.

This product meets and exceeds the requirements of UL 325, the standard which regulates gate operator safety, 

as established and made effective March 1, 2000, by Underwriters Laboratories Inc.

Installation Manual

 for the

SINGLE Gate Operator System

FOR PROFESSIONAL INSTALLATION ONLY!

For more information on GTO/PRO’s full line of automatic gate openers and access controls visit our website at www.gtopro.com

Содержание 4000XL











































Отзывы: