GST GST303 Скачать руководство пользователя страница 3

Страница: 3 / 28

GST303 /GST306
Extinguishing Control Panel

Installation and Operation Manual

Page 1

1 General

GST303/GST306 Extinguishing Control Panel (hereinafter called the control panel) is

designed for driving the executing units of a fixed extinguishing system.

Except for 3 extinguishing zones less, and some minor differences in appearance and

structure, GST303 is the same as GST306 in operation. We

’ll take GST306 as an

example.

2 Features

The control panel can be directly connected to the loop of GST intelligent fire alarm

control panels (FACP) that are able to control associated fire suppression equipment to

achieve automatic control of gas release.

It can also control gas release devices independent of the FACP. When the FACP is

not working properly, it can still control extinguishing devices through emergency gas

override control in field or

Start

and

Stop

keys on the control panel.

This control panel is also able to monitor and alarm on short circuit or open circuit with

externals cables

3 Technical Specifications

1) Capacity:

GST303: Controlling maximum 3 extinguishing zones (3 control units)

GST306: Controlling maximum 6 extinguishing zones (6 control units)

2) Delay Time: 0s

～

45s, adjustable by every 5s

3) Wiring:

a 2-core connection with FACP.

b Two-wire connection with the solenoid of cylinder, pressure switch

and gas extinguishing warning indicator.

c Three-wire connection with emergency gas override control.

d Two-wire connection with sounder strobe.

4) Power supply: Powered by external 20VDC~28VDC from intelligent PSU.

Total length from PSU to the control panel and from the control panel to

solenoid should not be over 100m, cross section not less than 2.5mm

5) Solenoid Interface:

Start output: By pulse or electric level mode. 5s for pulse mode; Voltage range:

18VDC

～

26VDC; Maximum current: 2A

6) Gas Extinguishing Warning Indicator Interface:

Start output: Voltage range: 18VDC

～

26VDC; Maximum current: 300mA

Load: Maximum 5 for each zone.

7) C-9316 Gas Stop Indicator Interface:

Start Output: Voltage: 18VDC~26VDC; Maximum Current: 100mA

Load: Maximum 3 for each zone.

8) Sounder Strobe Interface:

Содержание GST303





























Результаты поиска

Содержание GST303

Отзывы:

Бренды по названию

Популярные бренды

GST GST303, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GST303

Отзывы:

Бренды по названию

Популярные бренды