manualshive.com logo in svg

GST GST303, Инструкция по установке и эксплуатации

Поделиться
Скачать
GST GST303 Скачать руководство пользователя страница 18

GST303 /GST306 
Extinguishing Control Panel

                                         

 

                               

Installation and Operation Manual 

 

                                                           

 

 

Page 16 

dump” fault.

 

h)  Disconnect any cable between control panel  and protection door, the FACP 

reports 

“Gas dump” fault.

 

5.8 Installation of Protective Cover 

After mounting and commission, install the protective cover for start key  and stop key.   

Refer to Appendix 2 for installation method.

 

 

6  Operation 

 

6.1 Powering-up, Self-test and Switching off 

(1) Check the settings of the control panel according to Section 5. 

(2) Power up the unit as follows: 

 

Turn on the primary and standby power. 

 

Turn on the power of the control panel. After the above operation, the control 
panel  starts  self-test  on  sound  and  LEDs.  After  self-test,  it  enters  standby 

state. 

 

Turn  on  primary/standby  power  switch  and 

Run

  switch  of  the  FACP.  It  will 

register  the  address  of  the  control  panel.  The  quantity  of  address  points 

occupied by gas extinguishing devices = the greatest zone number x 4 +1. 

 

Turn off the switches in reverse procedure of turning on. 

6.2 Basic Operation 

6.2.1 Start   

Important:  Because  extinguishing  device  will  finish  gas  extinguishing 

instantaneously  on  receiving  valid  start  command,  so  improper  operation  will 

result in great losses beyond remedy, even loss of life; On the other hand, it will 

affect fire protective ability of some important places in a certain period. Be very 

careful when starting these devices! 

Besides conditions of starting ordinary  devices, starting extinguishing devices should 

also meet the following conditions: 

①

    The  personnel  to  start  extinguishing  devices must  be well  trained  of  the  relative 

knowledge. 

②

    Confirming the fire condition that extinguishing devices has to be started. 

③

    Confirming that people in the protected zone have been evacuated. 

After  extinguishing  devices  have  been  started,  field  pressure  switch  will  feed  back 

answer  signal  of  device  action,  and  gas  extinguishing  warning  indicator  is  lit.  The 

control panel reports action of extinguishing devices to the FACP. 

There are two modes of starting extinguishing devices: immediate start and delay start. 

a)  Immediate Start   

When  personnel  on  duty  have  confirmed  fire  and  people  have  been  evacuated, 

extinguishing devices can be started immediately. The command can be given from the 

control panel or from the FACP. 

Содержание GST303





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды