background image

D-9107RExd

 

Digital Flame Proof Dual IR Flame Detector                

 

Installation and Operation Manual

   

                                                  

   

 

 

Page 5  

corrosion and fire.  

(3)  The  cable  layout  for  hazardous  explosive  area  must  comply  with 

corresponding  codes.  The  connecting  cable  can  be  copper-core  screened 

cable or explosion-proof hose with suitable junction thread matching with the 

detector taper thread of the cable nut (Fig. 7). 

(4)  The cable must enter the detector through the junction nut, and there must be 

an O-ring, a seal and a washer, as shown in Fig. 7. 

 

Fig. 7 

(5)  Connect  the  screen  cover  of  the  cable  with  the  protective  earth  inside  the 

detector. 

(6)  Terminals on the base are shown in Fig. 8. 

 FT1   FT2   AL1   AL2 

 

Fig. 8 

  Z1,  Z2:  Communication  loop  input  from  fire  alarm  control  panel.  Polarity 

insensitive. 

  D1, D2: 24VDC power input. Polarity insensitive. 

  AL1,  AL2:  Fire  alarm  contact  output.  Normally  open  contact.  Closed  in  fire 

alarm.  

  FT1, FT2: Fault contact output. Normally closed contact. Open in fault.  

The  loop  cable  and  the  power  shall  enter  the  detector  through  a  cable  nut,  and  the 

signal cable through another cable nut (Fig. 9). If no signal cable is needed, the cable 

outlet shall be inserted with an blanking element with O-ring.  

If Z1 and Z2 does not connect with the loop, they must be connected with D1 and D2 

polarity-insensitively.  

 

 

 

 

 

 

 

 

Содержание D-9107RExd












Отзывы: