GSi NCHT X Series Скачать руководство пользователя | Manualshive

Страница: 6 / 62

background image

2. Safety

6

PNEG-1785

NCHT “X” Series Ladders

General Safety Statement

Our foremost concern is your safety and the safety of others associated with this equipment. This manual
is to help you understand safe operating procedures and some problems which may be encountered by
the operator and other personnel.

As owner and/or operator, you are responsible to know what requirements, hazards and precautions exist
and inform all personnel associated with the equipment or in the area. Safety precautions may be required
from the personnel. Avoid any alterations to the equipment, which may produce a very dangerous
situation, where SERIOUS INJURY or DEATH may occur.

You should consider the location of the bin site relative to power line locations or electrical transmission
equipment. Contact your local power company to review your installation plan or for information
concerning required equipment clearance. Clearance of portable equipment that may be taken to the bin
site should also be reviewed and considered. Any electrical control equipment in contact with the bin
should be properly grounded and installed in accordance with National Electric Code provisions and other
local or national codes.

This product is intended for the use of grain storage only. Any other use is a misuse of the product.

Sidewall bundles or sheets must be stored in a safe manner. The safest method of storing sidewall
bundles is laying horizontally with the arch of the sheet upward, like a dome. Sidewall sheets stored on
edge must be secured so that they cannot fall over and cause injury. Use care when handling and moving
sidewall bundles.

Personnel operating or working around equipment should read this manual. This manual must be
delivered with equipment to its owner. Failure to read this manual and its safety instructions is a misuse
of the equipment.

This product has sharp edges, which may cause serious injury. To avoid injury, handle
sharp edges with caution and always use proper protective clothing and equipment.

«
...
4
5
6
7
8
...
»

Содержание NCHT X Series































































Отзывы:

Нет отзывов

Похожие инструкции для NCHT X Series

On-the-Go 2021097938

Бренд: Lippert Страницы: 8

KW 5.50 / 4 x 7 T

Бренд: Krone Страницы: 42

Бренд: Skywalker Страницы: 7

Бренд: FACAL Страницы: 20

Бренд: GSSIM Страницы: 8

Бренд: Mac allister Страницы: 24

Бренд: Norstep Страницы: 109

Бренд: Youngman Страницы: 4

Бренд: KRAUSMANN Страницы: 8

Бренд: Hard Head Страницы: 24

Бренд: Quik Stage Страницы: 4

E-PWP7101AL Jobsite series

Бренд: MetalTech Страницы: 2

Бренд: Sperian Страницы: 18

Бренд: Rivers Edge Treestands Страницы: 20

Бренд: Ribimex Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды