GSi NCHT X Series Скачать руководство пользователя | Manualshive

Страница: 10 / 62

background image

2. Safety

10

PNEG-1785

NCHT “X” Series Ladders

Proper Storage of Grain Bin/Silo Materials Prior to Construction

Wet storage stain (rust) will develop when closely packed bundles of galvanized material, such as sidewall
and roof sheets, have moisture present. Inspect roof and sidewall bundles on arrival for any moisture. If
moisture is present, it must not be allowed to remain between the sheets. Separate the sheets or panels
immediately and wipe them down. Spray with a light oil or diesel fuel.

If possible, sidewall bundles, roof sheets and other closely packed galvanized materials should be stored
in a dry, climate controlled building. If outdoor storage is unavoidable, the materials should be stored so
that they are raised above the ground and vegetation. Any stacking and spacing materials should not be
corrosive or wet. Be sure to protect materials from the weather, but permit air movement around the
bundles if possible.

Storing roof bundles and sidewall sheets at a slight incline can also help minimize the presence of
moisture. Storing the bundles with the center of the dome up (like an arch) is one option for minimizing
moisture during storage. Sidewall bundles can also be stored on edge but must be secured so that they
do not fall over and cause injury.

If “white rust” or “wet storage stain” occurs, contact the manufacturer immediately about ways to minimize
the adverse effect upon the galvanized coating.

«
...
8
9
10
11
12
...
»

Содержание NCHT X Series































































Отзывы:

Нет отзывов

Похожие инструкции для NCHT X Series

Rainbow Attic Stair Galaxy G2755

Бренд: SP PARTNERS Страницы: 17

Бренд: Arke Страницы: 17

Бренд: Batavia Страницы: 2

Бренд: Fieldmann Страницы: 12

Бренд: MTF Страницы: 50

Бренд: Green Brook Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды