GSi 40 Series Скачать руководство пользователя страница 96

Страница: 96 / 116

Installing the Inside Ladder Bottom Bracket

The ladder bottom bracket keeps the lower portion of the ladder secure.

What You Should Know

The lower portion of the ladder may need to be cut to fit properly. Field drilling will be required to complete
installation.

1. Ensure the bottom of the ladder (A) is raised 12 in. (38.5 cm) from the floor.

NOTE:

If the ladder is not 12 in. (38.5 cm) from the floor, cut to specification.

2. Attach the two ladder bottom brackets (B) to the inside portion of the ladder assembly (A).

3. Align the holes in the sidewall with the ladder bottom bracket (B), and install 5/16 x 1 in. flange bolts

(E) and 5/16 in. flange nuts (C).

4. Field drill two 3/8 in. holes (D) as shown, and install the remaining 5/16 x 1 in. flange bolts (E) and

5/16 in. flange nuts (C), securing the ladder bottom bracket (B) to the sidewall.

5. Field drill six 3/8 in. holes (F) as shown, and install 5/16 x 1 in. flange bolts (G) and 5/16 in. flange

nuts (H).

6. Repeat this procedure for the second ladder bottom bracket (B).

7. Tighten hardware to the recommended torque specifications. Refer to

Bolt Torque Specifications,

page 26

Figure 9-4

Bottom ladder bracket

Ladder assembly

Ladder bottom bracket (LDR–5133)

5/16 in. flange nut (S-3611)

3/8 in. field drilled hole location

5/16 x 1 in. flange bolt with sealing washer
(S-10260)

3/8 in. field drilled hole location

5/16 x 1 in. flange bolt with sealing washer
(S-10260)

5/16 in. flange nut (S-3611)

PNEG-4336

36 Ft. Diameter 40-Series Bins

Содержание 40 Series





















































































































Результаты поиска

Содержание 40 Series

Отзывы:

Похожие инструкции для 40 Series

Бренды по названию

Популярные бренды

GSi 40 Series, Руководство по монтажу

Результаты поиска

Содержание 40 Series

Отзывы:

Похожие инструкции для 40 Series

Бренды по названию

Популярные бренды