manualshive.com logo in svg

GSi 24' Gamma, Руководство по установке

Поделиться
Скачать
GSi 24' Gamma Скачать руководство пользователя страница 30

4. Roof Assembly

30

PNEG-2262

 24' Diameter Gamma Roof Assembly Instructions

Attaching the Roof Panels

Roof panels overlap the previous roof panel, giving protection from the outside elements. Rafters and roof 
panel support clips will support to hold the roof panels.

Before You Begin

Ensure all the roof rafter assemblies and purlins are installed and properly tightened. Pre-determine the 
manway access location. Make sure the roof panel support clips are attached on the purlins before 
installing the roof panels (1).

What You Should Know

For adjustment purposes, roof panels (1) are installed to each rafter first, causing exposed gaps (2) 
between each roof panel (1) group. After all the roof panels are installed, ensure that all installed hardware 
(flange bolts with sealing washers and flange nuts) are tightened to secure the roof panels.

Figure 4R 

Roof Panel Overview

NOTE:

 

When installing the roof panels, take into consideration placing the manway for ease of access to 

and from the sidewall and the roof ladders.

1. With assistance, position a roof panel (1) onto the roof rafter (4) and install a 5/16" x 1" flange bolt (7) 

and 5/16" flange nut (8) securing the upper portion of the roof panel (1).

2. Install five 5/16" x 1" flange bolts (7) and 5/16" flange nuts (8), into the lower portion of the roof

panel (1), securing the roof panel (1) to the intermediate eave angle (6) and eave clips (5).

3. Working in a clockwise direction, continue installing the roof panels (1) to each roof rafter (4), leaving 

an exposed gap (2) between each installed roof panel.

Ref #

Part #

Description

1

CTR-0382

Roof Panel

2

Exposed Gap

Содержание 24' Gamma









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды