manualshive.com logo in svg

GSD Wi-Corporate Controller, Инструкция по установке и эксплуатации

Поделиться
Скачать
GSD Wi-Corporate Controller Скачать руководство пользователя страница 7

12

Operation Instructions

Setting up TCP-IP - Static IP

Step   Description

          

Note: see help video on the GSD CD for Static IP address setup

  1.     Default the Controller. See Restore Factory settings on page 11. The
          Controllers default IP address is 

169.254.1.1

.

  2.     Set the Controller address to address 1. See page 11 for details.
  3.     Connect the Controller directly to a PC to using an ethernet cable.

          

Connecting the Controller directly to a PC using default IP address..

  4.     Connect an Ethernet cable between the Controller and the PC. (The default
          IP address of the Controller is 

169.254.1.1

)

  5.     Set the IP address on the PC to a similar IP address e.g. 169.254.1.2
          

Note:

 If there is no LED activity on your PC’s ethernet interface then the PC

          requires a cross-over cable between the PC and the Controller.

  6.     Open the GSDWin application.
          On the Controller tab, Select TCP/IP with Static option and enter the
          default Controller IP address of 

169.254.1.1 

and click apply. The

          Controller icon will turn blue when it comes online. A new IP address can
          then be sent to the Controller using the “Controller TCP/IP Configuration”
          button.
          

Sending a new IP address to the Controller e.g 192.168.1.26.

   7.    Make sure the controller is online and click on the
          “Controller TCP/IP Configuration” button.
   8.    Choose Static IP mode and enter the IP address,
          Netmask and Default Gateway assigned by your
          network administrator. Click “Send new settings
          to Controller”. The Controller will now go offline as
          the new IP Address settings are applied.

   9.    Connect the PC and Controller to your LAN
          and enter the new IP address to allow the
          application to communicate with the
          Controller.
          Note: Reset the IP address on your PC to its
          original setting for your LAN.

 13

Operation Instructions

Setting up TCP-IP - DHCP

Step   Description

          

Note: see help video on the GSD CD for DHCP setup.

  1.     Default the Controller. See Restore Factory settings on page 11. The
          default TCP/IP mode will then be set to DHCP.
  2.     Set the Controller address to address 1. See page 11 for details.

          

Connecting the Controller to your DHCP LAN.

  

1.     Connect the Controller to your LAN using an ethernet cable. The Controller

          will be assigned an IP address automatically by your DHCP server.

2.       Open the GSDWin application. On the Controller tab, Select TCP/IP
          with the DHCP option and enter the MAC address of the Controller and
          click “Apply”.
          The MAC address of the controller can be found on the box or printed on
          the Controller PCB. The Controller icon will turn blue when it comes online.

Содержание Wi-Corporate Controller















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды