background image

Common  hardware  items  such  as  nuts,  bolts,  star  washers,  lock  washers  and  the
like  have  not  been  evaluated  for  electrical  conductivity  or  for  use  as  grounding
devices  and  should  be  used  only  for  maintaining  mechanical  connections  and
holding  electrical  grounding  devices  in  the  proper  position  for  electrical
conductivity.  Such  devices,  where  supplied  with  the  module  and  evaluated
through  the  requirements  in  UL  1703,  may  be  used  for  grounding  connections  in
accordance with the instructions provided with the module.
Grounding methods below are permissible:

7.1 Grounding by grounding clamp

There is a grounding hole with the diameter of Ø4.2mm at the edge of the module
back  frame.  The  central  line  of  the  grounding  sign  and  that  of  the  hole  overlaps
and is consistent with the frame length direction.
Grounding  between  modules  shall  be  confirmed  by  qualified  electricians  and
grounding  devices  shall  be  manufactured  by  qualified  electric  manufacturer.  The
torque is recommended to be 2.3N•m.
12  AWG  copper  core  wire  is  used  for  the  grounding  clamp.  And  copper  wires  can
not be pressed damaged in installation.

Installation Manual PV Modules High Power Half Cut

15

Содержание SOLARGREEN VE4 PV Series





















Отзывы: