Gruppo Ferroli FZ4B, Инструкции по использованию и установке

Страница: 81 / 292

CONTROLLO ZONE FZ4B
81
cod. FZ4B - 06/2011 (Rev. 00)
EN
One mixed zone, one direct zone and one hot water tank circuit
Schematic diagram
Use 3-wire mixing valves:
- OPENING PHASE 230V
- CLOSING PHASE 230V
- NEUTRAL.
with switching times (from all closed to all open) of not more than
180 seconds.
• Management of priority/contemporaneity with parameter FZ4B P25
• Management of Economy/Comfort only with Remote Timer Control
CALDAIA
M
318a
317a
319a
315a
a
318b
b
318c
155
c
72a/139a 72b/139b
fi g. 32
Electrical connections
After installation, carry out the necessary electrical connections as shown in the wiring diagram.
Then con
fi gure the controller as described in the speci fi c section.
RY1 RY2 RY3 RY4 RY5 RY6 RY7 RT1 RT2 RT3 T1 T2 T3 T4
7 (L) 8 (N) 9 (L) 10 (N) 11 (L) 12 (L) 13 (L) 14 (N) 15 (L) 16 (L) 19 - 20 21 - 22 23 - 24 25 - 26 27 - 28 29 - 30 30 - 31
318a 318a 315a - A 315a - B 315a - C 318b 318b/318c 318c 72a/139a 72b/139b 319a 155
318a 318a 315a - A 315a - B 315a - C 318b 318b/318c 318c 72a/139a 72b/139b 319a 155 138
318a
317a
318b 315a 139a
72a
139b
72b
319a
138
230Vac
50Hz
L
N
IMPIANTO
A B C
155
318c
FZ4B
X15
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2526 27 28 29 3031 32 33
L_N L_N L_N L L_N L L L
X01 X02 X03 X09 X10 X11 X12 X13 X14
BUSRT1 RT2 RT3 T1 T2 T3T4 BLR
fi g. 33
72a 1st zone (mixed) room thermostat
72b 2nd zone (direct) room thermostat
138 External probe
139a 1st zone (mixed) Remote Timer Control
139b 2nd zone (direct) Remote Timer Control
315a 1st zone (mixed) mixing valve
A = OPENING PHASE
B = NEUTRAL
C = CLOSING PHASE
155 Hot water tank probe
317a 1st zone (mixed) safety thermostat
318a 1st zone (mixed) circulating pump
318b 2nd zone (direct) circulating pump
318c Hot water tank circulating pump
319a 1st zone (mixed) delivery sensor
a 1st zone (mixed)
b 2nd zone (direct)
c Hot water tank circuit
____ Necessary wiring
- - - - Optional wiring
In case of Stand Alone 2 con fi guration it is necessary to purchase the NTC probe accessory code 1KWMA11W (2 mt.) or code 043005X0 (5 mt.)
To manage the sliding temperature it is necessary to purchase the external probe accessory code 013018X0
If a hot water tank thermostat (not supplied) is used, it is necessary to purchase the accessory kit code 013017X0 (to be connected in place of the Hot water tank Probe)