Grundfos TPE 2 Series Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 70

background image

English (GB)

63

Analog output (AO)

Current sourcing capability only.
Voltage signal:
• Range: 0-10 VDC.
• Minimum load between AO and GND: 1 k

Ω

.

• Short-circuit protection: Yes.
Current signal:
• Ranges: 0-20 and 4-20 mADC.
• Maximum load between AO and GND: 500

Ω

.

• Open-circuit protection: Yes.
Tolerance: - 0/+ 4 % of full scale (max-point coverage).
Screened cable: 0.5 - 1.5 mm

2

/ 28-16 AWG.

Maximum cable length: 500 m.

Pt100/1000 inputs (PT)

Temperature range:
• Minimum -50 °C (80

Ω

/803

Ω

).

• Maximum 204 °C (177

Ω

/1773

Ω

).

Measurement tolerance: ± 1.5 °C.
Measurement resolution: < 0.3 °C.
Automatic range detection (Pt100 or Pt1000): Yes.
Sensor fault alarm: Yes.
Screened cable: 0.5 - 1.5 mm

2

/ 28-16 AWG.

Use Pt100 for short wires.
Use Pt1000 for long wires.

LiqTec sensor inputs

Use Grundfos LiqTec sensor only.
Screened cable: 0.5 - 1.5 mm

2

/ 28-16 AWG.

Grundfos Digital Sensor input and output (GDS)

Use Grundfos Digital Sensor only.

Power supplies (+5 V, +24 V)

+5 V:

• Output voltage: 5 VDC - 5 %/+ 5 %.
• Maximum current: 50 mADC (sourcing only).
• Overload protection: Yes.

+24 V:

• Output voltage: 24 VDC - 5 %/+ 5 %.
• Maximum current: 60 mADC (sourcing only).
• Overload protection: Yes.

Digital outputs (relays)

Potential-free changeover contacts.
Minimum contact load when in use: 5 VDC, 10 mA.
Screened cable: 0.5 - 2.5 mm

2

/ 28-12 AWG.

Maximum cable length: 500 m.

Bus input

Grundfos GENIbus protocol, RS-485.
Screened 3-core cable: 0.5 - 1.5 mm

2

/ 28-16 AWG.

Maximum cable length: 500 m.

30. Other technical data

EMC (electromagnetic compatibility)

EN 61800-3.
Residential areas, unlimited distribution, corresponding to CISPR
11, class B, group 1.
Industrial areas, unlimited distribution, corresponding to CISPR
11, class A, group 1.
Contact Grundfos for further information.

Enclosure class

Standard: IP55 (IEC 34-5).
Optional: IP66 (IEC 34-5).

Insulation class

F (IEC 85).

Torques

Terminal

Thread size

Max. torque

[Nm]

L1, L2, L3, L, N

M4

1.8

NC, C1, C2, NO

M2.5

0.5

1 to 26 and A, Y, B

M2

0.5

«
...
61
62
63
64
65
...
»

Содержание TPE 2 Series







































































Отзывы:

Нет отзывов

Похожие инструкции для TPE 2 Series

Бренд: ABB Страницы: 11

Бренд: Parker Страницы: 54

Бренд: Yamaha Страницы: 78

Бренд: Fast Страницы: 42

Бренд: DARAY Страницы: 28

Бренд: Haenim Страницы: 2

Бренд: Panasonic Страницы: 30

Бренд: EAW Страницы: 2

Бренд: abc Страницы: 28

Бренд: OceanSat Страницы: 85

Бренд: JB-Lighting Страницы: 32

Бренд: W&H Страницы: 72

Бренд: Jet Страницы: 12

Бренд: Zimmer Страницы: 54

Бренд: Zimmer Страницы: 4

Бренд: Zimmer Biomet Страницы: 23

Бренд: Zimmer Страницы: 16

Бренд: Zimmer Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды