Grundfos TPE 2 Series Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 70

background image

English (GB)

4

3. General information

These installation and operating instructions apply to the
Grundfos TPE2, TPE2 D and TPE3, TPE3 D pumps.
The pumps are fitted with frequency-controlled
permanent-magnet motors for single-phase or three-phase mains
connection.

3.1 Radio communication

This product incorporates a radio module for remote control
which is a class 1 device and can be used anywhere in the EU
without restrictions.
For use in USA and Canada, see page

This product can communicate with Grundfos GO and other
products of the same type via the built-in radio module.
In some cases, an external antenna may be required.
Only Grundfos-approved external antennas may be connected to
this product, and only by a Grundfos-approved installer.

3.2 Battery

Pumps with the advanced functional module, FM 300, incorporate
a Li-ion battery. The Li-ion battery complies with the Battery
Directive (2006/66/EC). The battery does not contain mercury,
lead and cadmium.

4. Delivery and handling

4.1 Delivery

The pump is delivered from the factory in a carton with a wooden
bottom, specially designed for transport by fork-lift truck or a
similar vehicle.

4.2 Handling

Lift the pump by means of nylon straps. See figures

and

Fig. 1

TPE2, TPE3

Fig. 2

TPE2 D, TPE3 D

Note

Some variants of these products and all products
sold in China and Korea have no possibility of radio
communication according to local legislation.

Warning
TPE2 D, TPE3 D: Do not use the centrally positioned
thread of the pump housing for lifting purposes as the
thread is placed below the centre of gravity of the
pump.

TM

05

79

14

16

13

TM

05 791

5 161

3

«
...
2
3
4
5
6
...
»

Содержание TPE 2 Series







































































Отзывы:

Нет отзывов

Похожие инструкции для TPE 2 Series

ACS880-01 Series

Бренд: ABB Страницы: 238

Бренд: Bartscher Страницы: 28

Бренд: Bartscher Страницы: 13

Бренд: IBEX Страницы: 10

Бренд: M-system Страницы: 12

Бренд: Danelec Страницы: 67

Бренд: Eaton Страницы: 16

RMQ-Titan C22-PV Series

Бренд: Eaton Страницы: 6

Бренд: Eaton Страницы: 98

Бренд: Eaton Страницы: 15

Бренд: Hacker Страницы: 2

Бренд: J.P. SELECTA Страницы: 8

Бренд: Haemonetics Страницы: 134

Бренд: Hadeco Страницы: 72

Бренд: Vahterus Страницы: 31

Бренд: Jackson Страницы: 2

Cell Saver Elite+

Бренд: Haemonetics Страницы: 230

Бренд: +GF+ Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды