Grundfos Redi-Flo Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 16

Grundfos Redi-Flo Series Скачать руководство пользователя страница 8

8

REDI-FlO VFD SPECIAl FEATURES

Dual Input Capability

Redi-Flo VFD can accept 5V or 230V single phase input voltage

Enclosure

The Redi-Flo VFD NEMA 4 enclosure is designed for outdoor duty and is resistant to damage as a result of
incidental exposure to rain.

UL Approvals

The Redi-Flo VFD is UL Listed to U.S. and Canadian electrical safety standards.

Dual Functionality

The Redi-Flo VFD can change from operating Redi-Flo2® (MP) to Redi-Flo4™ (SPE) Variable Performance
pumps with a few keystrokes.

Torque Boost

The Redi-Flo VFD is equipped with a torque boost (voltage boost) feature to aid in start-up under severe
conditions.

Optimized Volts/Frequency (V/HZ) Pattern

The Redi-Flo VFD V/Hz pattern is specially optimized to allow the most efficient operation of Redi-Flo2® and
Redi-Flo4™ variable performance pumps.

«
...
6
7
8
9
10
...
»

Содержание Redi-Flo Series

















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды