Grundfos DMX 227 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 24

Grundfos DMX 227 Скачать руководство пользователя страница 6

English (GB)

6

3.4 Suction heights

• Data in mWC.
Applies to:
• non-degassing and non-abrasive media
• Newtonian liquids
• temperature of 20 °C
• standard pump version.

3.4.1 Media with a viscosity similar to water

Maximum suction height: 3 mWC.

3.4.2 Suction heights for media with maximum permissible

viscosity

Flooded suction: 1-3 mWC.

3.5 Ambient and operating conditions

• Permissible ambient temperature: 0 °C to +40 °C.
• Permissible storage temperature: -20 °C to +50 °C.
• Permissible air humidity: max. relative humidity

(non-condensing): 70 % at 40 °C, 90 % at 35 °C.

• Sound pressure level: 70 ± 5 dB(A), testing according to

DIN 45635-01-KL3.

• Minimum counterpressure: 1 bar at the pump discharge valve.

Pay attention to the pressure losses along the way to the
injection point inclusively.

• Minimum pressure on the suction side: 1 bar.

3.6 Dosing medium

The dosing medium must have the following basic characteristics:
• liquid
• non-abrasive
• non-flammable.

3.6.1 Permissible media temperature

* For SIP/CIP applications, a temperature of 145 °C at a

counterpressure of max. 2 bar is permitted for a short period
(15 minutes).

3.6.2 Maximum permissible viscosity

Applies to:
• non-degassing and non-abrasive media
• Newtonian liquids
• temperature of 20 °C
• standard pump version.

3.7 Electrical data

3.7.1 Enclosure class

The enclosure class depends on the motor variant selected, see
motor nameplate.
The specified enclosure class can only be ensured if the power
supply cable is connected with the same degree of protection.

3.7.2 Motor

Version: see motor and pump nameplates.

3.8 Materials

Pump

• Pump housing: Al 226
• Diaphragm flanges: GG 25.

Optoelectronic diaphragm sensor

• Housing: ABS.

3.9 Weights

Caution

The installation site must be under cover!
Ensure that the enclosure class of motor and pump
are not affected by the atmospheric conditions.
Pumps with electronics are only suitable for indoor
use! Do not install outdoors!

Warning
Risk of hot surfaces!
Pumps with AC motors may become hot.
Allow a minimum space of 100 mm above the fan
cover!

Caution

In the event of questions regarding the material
resistance and suitability of the pump for specific
dosing media, please contact Grundfos.

Dosing head material

Temperature range

p < 10 bar

PVC

0 °C to +40 °C

Stainless steel*

-10 °C to +70 °C

PP

0 °C to +40 °C

Caution

Observe the freezing and boiling points of the dosing
medium!

Pump type

Viscosity

[mPa s]

50 Hz

60 Hz

DMX 860-5

800

400

DMX 1120-5

400

200

DMX 1520-3

400

200

DMX 2000-3

200

100

Approx. weight

[kg]

Single-head pumps

50

Double-head pumps

90

«
...
4
5
6
7
8
...
»

Содержание DMX 227

























Отзывы:

Нет отзывов