Grundfos DMX 227 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 24

Grundfos DMX 227 Скачать руководство пользователя страница 18

English (GB)

18

10.4 Replacing the diaphragm

10.4.1 Switching off the pump

1. Switch off the pump and disconnect it from the power supply.
2. Depressurise the system.
3. Take suitable steps to ensure that the returning dosing

medium is safely collected.

10.4.2 Replacing the diaphragm

1. Loosen the six dosing head screws.
2. Remove the dosing head.
3. Unscrew the diaphragm by manually turning it

counter-clockwise.

4. Refit the retaining ring (4), shim ring (5), lip seal (7) and

supporting ring (6). Replace faulty parts.

5. Screw in the new diaphragm completely.
6. Remove the motor fan cover, and turn the fan blades until the

diaphragm reaches the bottom dead centre.

7. Refit the dosing head carefully, and cross-tighten the screws.

Maximum torque: 70-80 Nm.

8. Deaerate and start the dosing pump.

Fig. 19

Replacing the diaphragm

Grundfos gear oil

Alternative special oil for DHG 68

Note

If possible, rinse the dosing head, e.g. by supplying it
with water.

TM

03

7

189

45

0

6

Pos.

Components

1

Diaphragm

2

Dosing head screws

3

Dosing head

4

Retaining ring

5

Shim ring

6

Supporting ring

7

Lip seal

Caution

After initial start-up and after each time the
diaphragm is changed, tighten the dosing head
screws.
After approximately 6-10 operating hours or two
days, cross-tighten the dosing head screws using a
torque wrench.
Maximum torque: 70-80 Nm.

2

3

6

1

4

5

7

Order no

Description

98683958

5.0 l DHG 68

98683959

7.5 l DHG 68

Manufacturer

Designation

ARAL

Degol BMB 68

BP

BP-Energol GR-XP 68

Chevron

Chevron NL gear compound 68

ESSO

Spartan BP 68

Fina

Fina Giran 68

Mobil Oil

Mobilgear 626

Texaco

Texaco Meropa 68

Shell

Tellus 68

elf

reductelf SP 68

«
...
16
17
18
19
20
...
»

Содержание DMX 227

























Отзывы:

Нет отзывов