Grundfos CRN 125-7 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 38

background image

TM068598

Vertical lift of pumps with 10-30 HP (7.5 - 22
kW) Grundfos ML, MLE and MG, MGE motors

TM068599

Vertical lift of pumps with 7.5 - 250 HP (5.5 -
200 KW) motors of other makes than Grundfos
ML, MLE and MG, MGE motors

TM068162

Vertical lift of pumps without a motor

5. Mechanical installation

DANGER

Falling objects

Death or serious personal injury

‐

Fasten the pump securely to a solid
and even foundation according to
the specifications stated in the
installation and operating
instructions.

WARNING

Contamination when pumping
drinking water

Death or serious personal injury

‐

Before the pump is used for
supplying drinking water, flush the
pump thoroughly with clean water.

‐

Do not use the pump for drinking
water if the internal parts have
been in contact with particles or
substances not suitable for water
intended for human consumption.

WARNING

Falling objects

Death or serious personal injury

‐

Do not use the motor eyebolts to lift
the entire pump if the pump is fitted
with a motor of another make than
Grundfos ML, MLE and MG, MGE.

‐

Follow the lifting instructions.

‐

Use lifting equipment which is
approved for the weight of the
product.

‐

Persons must keep a safe distance
to the product during lifting
operations.

‐

Wear personal protective
equipment.

For lifting instructions, see the section on lifting
the product.

Related information

4.4 Lifting the product

13

English (US)

«
...
11
12
13
14
15
...
»

Содержание CRN 125-7







































Отзывы:

Нет отзывов

Похожие инструкции для CRN 125-7

Бренд: A.O. Smith Страницы: 56

Бренд: Nastec Страницы: 28

Бренд: WAGNER Страницы: 100

flexoTHERM exclusive VWF 57/4

Бренд: Vaillant Страницы: 20

AquaMax Eco Expert

Бренд: Oase Страницы: 60

Craftsman 390.269451

Бренд: Sears Страницы: 8

Бренд: Daalderop Страницы: 16

Бренд: Takagi Страницы: 64

Бренд: Ingersoll-Rand Страницы: 12

Бренд: QED Страницы: 33

DynaDrive DD60-10

Бренд: Davey Страницы: 32

Hydra-Cell G-25

Бренд: Wanner Engineering Страницы: 20

JUNG PUMPEN SIMER 4

Бренд: Pentair Страницы: 10

Gast 1HAB-25 Shown

Бренд: Idex Страницы: 14

RSJ-100/N1-540V-D

Бренд: Midea Страницы: 47

HPWH 3.1 200 U02

Бренд: TESY Страницы: 77

POWER VENTED GAS Models

Бренд: PowerFlex Страницы: 60

Бренд: WITA Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды