Grundfos ALPHA SOLAR 15-75 130 Скачать руководство пользователя | Manualshive

Страница: 9 / 40

background image

English (GB)

9

5. Starting up the product

5.1 Before startup

Do not start the pump until the system has been filled with liquid
and vented. Make sure that the required minimum inlet pressure
is available at the pump inlet.
See sections

3. Installing the product

and

10. Technical data and

installation dimensions

5.2 Venting the pump

Fig. 12

Venting the pump

The pump is self-venting. You do not have to vent the pump
before startup.
Air in the pump may cause noise. This noise ceases when the
pump has run for a few minutes.
You obtain quick venting of the pump by setting the pump to
speed III for a short period. How fast the pump is vented depends
on the system size and design.
When you have vented the pump, i.e. when the noise has
ceased, set the pump according to the recommendations. See
section

7. Control functions

.

You cannot vent the system through the pump. See section

5.3 Venting the heating system

.

5.3 Venting the heating system

Fig. 13

Venting of the heating system

Vent the heating system as follows:
• via an air vent valve installed above the pump (1)
• via a pump housing with air separator (2).
In heating systems that often contain much air, we recommend
that you install pumps with pump housing with air separator, i.e.
ALPHAx XX-XX A.
When the heating system has been filled with liquid, do as
follows:
1. Open the air vent valve.
2. Set the pump to speed III.
3. Let the pump run for a short period
4. Set the pump according to the recommendations. See section

7. Control functions

Repeat the procedure, if necessary.

5.4 First startup

• The light in the control panel shows that the power supply has

been switched on. See fig.

• Factory setting: AUTO

ADAPT

.

TM

05 307

5 091

2

The pump must not run dry.

10 Min.

1

2

TM

03

89

31

27

07

The pump must not run dry.

W

40 180

A

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

40

4

4

4

4

40

0

0

4

4

4

4

0

0

4

40

4

4

4

4

40

0

4

4

0

4

4

4

0

180

A

A

A

A

10 Min.

2

1

3

«
...
7
8
9
10
11
...
»

Содержание ALPHA SOLAR 15-75 130









































Отзывы:

Нет отзывов

Похожие инструкции для ALPHA SOLAR 15-75 130

AquaMax Eco Expert 21000

Бренд: Oase Страницы: 136

Бренд: Nastec Страницы: 28

Бренд: SAER Elettropompe Страницы: 16

Bell & Gossett ecocirc XL Series

Бренд: Xylem Страницы: 62

Бренд: Graco Страницы: 56

Streamline 270MDV

Бренд: Solahart Страницы: 56

Signature XP19-024

Бренд: Lennox Страницы: 32

Бренд: IDEAL Страницы: 30

Бренд: CLIVET Страницы: 7

Бренд: Gorenje Tiki Страницы: 48

Pacific Hydrostar 2" or 3" Dirty Water Pump...

Бренд: Pacific hydrostar Страницы: 36

Бренд: Yardworks Страницы: 19

Бренд: KABI Страницы: 6

Бренд: Dimplex Страницы: 12

Бренд: Lamborghini Caloreclima Страницы: 62

Бренд: FLOJET Страницы: 4

AirSite GreenMaster-HP 3-12/12

Бренд: Nibe Страницы: 104

RESIDENTIAL GAS FIRED WATER HEATERS

Бренд: Giant Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды