background image

  

 

GRUNDFOS 

INSTRUCTIONS

 

www.grundfos.co.uk 

Page 13 of 35  

                                                      

     

8.5 Frost protection 

  The 

FireSAFE

 unit must be protected from freezing conditions.  The unit may require 

trace heating or lagging. If the 

FireSAFE

 unit is being stored during periods of frost the whole 

unit should be drained to avoid damage.  Remove all drain and vent plugs and allow the pump 
to drain.  Do not replace the plugs until the 

FireSAFE

 unit is to be used again.   

  The pump must be vented/primed before it is started again.  

                

See section 5 for priming screw location.  

             Loosen but do not remove the priming screw until water flows from the hole. 

 

 

8.6 Operating enviroment 

  The 

FireSAFE

 unit must not be used in an environment which has been classified as 

hazardous where it could provide a source of ignition and therefore cause an explosion by 
flame path. 

 

Grundfos do not accept any responsibility for the use of 

FireSAFE

 unit to pump liquids which 

could be construed as being hazardous to health either by touch, ingestion or inhalation of 
fumes or gases given off by the liquid. 

 

8.7 Installation location 

Careful consideration must be given to the location of 

the FireSAFE

 unit.  

The following are minimum requirements: 

 The 

FireSAFE

 unit should ideally be placed in a location where the Control panel LEDs can 

readily be seen and the internal buzzer heard without obstruction.  

These are primary warning and alarm events and should be available to be observed and 

heard. Additional system provision for alerting the inhabitants to the 

FireSAFE

 warnings/alarm 

must also be made. 

  The 

FireSAFE

 also needs to be protected against the extremes of temperature during a 

Fire and during the winter. Provision to maintain the 

FireSAFE’s

 operating conditions needs to 

be made within the overall system design.  

  The 

FireSAFE 

unit should be sited in a dry, well ventilated, and frost-free position, where 

it will not be subjected to extremes of temperature.  

  The 

FireSAFE

 may be located outdoors in a weather, frost and rodent proof enclosure 

with adequate ventilation especially during hot weather.  All pipe work subject to freezing 
conditions must be adequately protected. Alternative system provision must be made for 
alerting the inhabitants to the 

FireSAFE

 warnings and alarms. 

 

To enable maintenance and service of the 

FireSAFE

 unit to be carried out satisfactorily, 

the area should have adequate lighting for this work to be carried out safely.  

Содержание 98916439





































Отзывы: