background image

10. Pressure sensor voltage chart

Voltage to pressure chart for EZ Boost pressure sensors. Measure DC voltage between Sensor IN and Sensor Ground.
Voltages less than 2 or greater than 10 indicate an incorrectly wired or a faulty sensor.

DC voltage 

psi

DC voltage 

psi

DC voltage 

psi

1.9

0.0

4.5

40.5

7.1

81.0

2.0

0.7

4.6

41.2

7.2

81.7

2.0

1.5

4.6

42.0

7.2

82.5

2.1

2.2

4.7

42.7

7.2

83.2

2.1

3.0

4.7

43.5

7.3

84.0

2.2

3.7

4.8

44.2

7.3

84.7

2.2

4.5

4.8

45.0

7.4

85.5

2.3

5.2

4.8

45.7

7.4

86.2

2.3

6.0

4.9

46.5

7.5

87.0

2.4

6.7

4.9

47.2

7.5

87.7

2.4

7.5

5.0

48.0

7.6

88.5

2.4

8.2

5.0

48.7

7.6

89.2

2.5

9.0

5.1

49.5

7.7

90.0

2.5

9.7

5.1

50.2

7.7

90.7

2.6

10.5

5.2

51.0

7.8

91.5

2.6

11.3

5.2

51.7

7.8

92.2

2.7

12.0

5.3

52.5

7.9

93.0

2.7

12.8

5.3

53.2

7.9

93.7

2.8

13.5

5.4

54.0

8.0

94.5

2.8

14.3

5.4

54.7

8.0

95.2

2.9

15.0

5.5

55.5

8.1

96.0

2.9

15.7

5.5

56.2

8.1

96.7

3.0

16.5

5.6

57.0

8.2

97.5

3.0

17.2

5.6

57.7

8.2

98.2

3.1

18.0

5.7

58.5

8.3

99.0

3.1

18.7

5.7

59.2

8.3

99.7

3.2

19.5

5.8

60.0

8.4

100.5

3.2

20.2

5.8

60.7

8.4

101.3

3.3

21.0

5.9

61.5

8.4

102.0

3.3

21.7

5.9

62.2

8.5

102.8

3.4

22.5

6.0

63.0

8.5

103.5

3.4

23.2

6.0

63.7

8.6

104.3

3.5

24.0

6.0

64.5

8.6

105.0

3.5

24.7

6.1

65.2

8.7

105.8

3.6

25.5

6.1

66.0

8.7

106.5

3.6

26.2

6.2

66.7

8.8

107.3

3.6

27.0

6.2

67.5

8.8

108.0

3.7

27.7

6.3

68.2

8.9

108.8

3.7

28.5

6.3

69.0

8.9

109.5

3.8

29.2

6.4

69.7

9.0

110.3

3.8

30.0

6.4

70.5

9.0

111.0

3.9

30.7

6.5

71.2

9.1

111.8

3.9

31.5

6.5

72.0

9.1

112.5

4.0

32.2

6.6

72.7

9.2

113.3

4.0

33.0

6.6

73.5

9.2

114.0

4.1

33.7

6.7

74.2

9.3

114.8

4.1

34.5

6.7

75.0

9.3

115.5

4.2

35.2

6.8

75.7

9.4

116.3

4.2

36.0

6.8

76.5

9.4

117.0

4.3

36.7

6.9

77.2

9.5

117.8

4.3

37.5

6.9

78.0

9.5

118.5

4.4

38.2

7.0

78.7

9.6

119.3

4.4

39.0

7.0

79.5

9.6

120.0

4.5

39.7

7.1

80.2

33

Instructions

EZ Boost

TM

 

System

LEZTL01.indd

10/8/2004, 1:39 PM

33

Содержание 15 BMQE 05A-110





































Отзывы: