Grohe RED 30 340, Руководство пользователя

Страница: 14 / 16

13
• Installation elevation:max. 2000 m above sea level
• Voltage supply:
230 V AC / 50 Hz
• Max. power consumption: 2200 W
• Type of protection: IP X4
• Relative humidity: max. 95 %
• Ambient temperature: 0–40 °C
• Standby power loss (switched on): M: 14 W
L: 15.7 W
• Standby power loss (holiday mode): M: 5 W
L: 7 W
• Standby power loss (switched off): 1 W
• Energy efficiency class: A
Sanitary data:
• Boiling water storage heater capacity: M: 4 l
L: 7 l
• Available storage heater volume at 100 °C: M: approx. 3 l
L: approx. 5.5 l
• Flow pressure:
- min. 0.2 MPa
- recommended 0.2–0.5 MPa
• Operating pressure: max. 0.8 MPa
• Test pressure: 1.6 MPa
• Flow rate at 0.3 MPa flow pressure
- mixed water: approx. 6 l/min
- boiling water: approx. 3 l/min
• Boiling water temperature: 100 °C
The actual temperature may differ slightly
due to different ambient pressures.
• Heating time from 10 °C to 100 °C: M: approx. 20 min
L: approx. 30 min
• Clamping length of fitting: max. 60 mm
• Water connection to storage heater: cold water
• Water connection fitting:cold/hot water from the service valve
boiling water from storage heater
The filter system with ion exchanger (S, M, L or Mg+) which is
included
must
be used in regions with a carbonate hardness
exceeding 10 °KH. The relevant water supplier can provide
information on the carbonate hardness.
Thermal disinfection of the fitting is possible.
Confirmation
Installation and commissioning
Flush pipes thoroughly before and after installation
(observe EN 806)
!
Adjust bypass of filterhead according to local carbonate
hardness and connect filter cartridge.
The carbonate hardness can be tested by using the enclosed test
strip or the relevant water supplier can provide information on the
carbonate hardness.
Note: The volume of water in the storage heater will expand as
it is heated. The expansion water must drip out of the funnel of
the safety assembly.
This is a necessary and completely normal process.
Check all connections for leakage.
Retighten screw connections as necessary.
Control:
The cooler/carbonator is set for operation with the S-Size filter
cartridge (Prod no.: 40 404 001) at the factory.
For operation with other filter cartridges the cooler/carbonator must be
switched over, see also page 8.
Operation , see page 9.
Unlock the child safety device to get boiling water, see
A
.
Key combination for filling pots with boiling water, see
B
.
To get cold or hot water, see
C
.
Activation of the holiday mode, see
D
.
Note:
In order to prevent incorrect operation and for protection against injury,
we recommend affixing the sticker provided.
Status Storage heater LED Fitting LED
Initialisation white -
Heating phase red, flashing -
Ready for operation red, continuous -
Holiday mode,
cooling-down phase
orange, flashing -
Holiday mode orange, continuous -
Child lock, unlocking
procedure
- red, flashing
Child lock, unlocked - red, continuous
Pot filling, unlocking
procedure
- yellow, flashing
Pot filling - yellow, continuous
Defects magenta,
flashing/continuous
magenta,
flashing/continuous
Button Display
Briefly press
PROG
button (
PRG
flashes)
Briefly press
RESET
button to access
programming for litre specification (0000
0
)
Keep pressing
PROG
button until required
position is reached (00
0
00 digit flashes)
Keep pressing
RESET
button until required
digit is reached (00
6
00 digit flashes)
Keep pressing
PROG
button to exit menu
(
PRG
disappears and set value appears)