13
for indoor use.
• The boiling water storage heater
must
be placed
in an upright position.
• The boiling water storage heater must
not
be
directly or indirectly sprayed with water when
cleaning.
• The boiling water storage heater must not be
opened.
• Use
only genuine replacement parts and
accessories
. The use of other parts will result in
voiding the warranty and the CE marking, and
could cause injury.
• Do not use a damaged device.
• The filter head
must be
replaced after 5 years by
the
GROHE service
.
• The use of extension cables is
not
permitted
between the electrical socket and boiling water
storage heater connection.
• The boiling water storage heater
must
be used
with the safety assembly supplied.
• To ensure uninterrupted function of the safety
assembly, it is advisable to have maintenance
work carried out regularly.
• The boiling water storage heater may only be
used with a GROHE Red fitting.
• Do
not
connect the hot water connection of the
fitting to the hot water outlet of the storage
heater. A mixing valve
must
be used (special
accessory *40 841), as necessary.
• If the operating pressure is insufficient, the
boiling water storage heater
must
be switched
off.
• In order to transport the boiling water storage
heater, it
must
first be emptied. To do this, the
safety assembly must be disconnected from the
boiling water storage heater.
Caution: risk of scalding.
Escaping water is
boiling hot.
• No liability can be accepted for damage that
occurs due to non-observance of the operating
instructions.
Technical data boiling water storage heater:
• Connection:
wall socket with earth wire,
protected via a 10 A fuse
• Installation elevation:
max. 2000 m above sea level
• Voltage supply:
230 V AC / 50 Hz
• Max. power consumption:
2200 W
• Type of protection:
IP X4
• Relative humidity:
max. 95 %
• Ambient temperature:
0–40 °C
• Standby power loss (switched on):
M: 14 W
L: 15.7 W
• Standby power loss (holiday mode):
M: 5 W
L: 7 W
• Standby power loss (switched off):
1 W
• Energy efficiency class:
A
Sanitary data:
• Boiling water storage heater capacity:
M: 4 l
L: 7 l
• Available storage heater volume at 100 °C:
M: approx. 3 l
L: approx. 5.5 l
• Flow pressure:
- min.
0.2 MPa
- recommended
0.2–0.5 MPa
• Operating pressure:
max. 0.8 MPa
• Test pressure:
1.6 MPa
• Flow rate at 0.3 MPa flow pressure
- mixed water:
approx. 6 l/min
- boiling water:
approx. 3 l/min
• Boiling water temperature:
100 °C
The actual temperature may differ slightly
due to different ambient pressures.
• Heating time from 10 °C to 100 °C:
M: approx. 20 min
L: approx. 30 min
• Clamping length of fitting:
max. 60 mm
• Water connection to storage heater:
cold water
• Water connection fitting:
cold/hot water from the service valve
boiling water from storage heater
The filter system with ion exchanger (S, M, L or Mg+) which is
included
must
be used in regions with a carbonate hardness
exceeding 10 °KH. The relevant water supplier can provide
information on the carbonate hardness.
Thermal disinfection of the fitting is possible.
Confirmation
Status
Storage heater LED
Initialisation
white
Heating phase
red, flashing
Ready for operation
red, continuous
Holiday mode, cooling-down
phase
orange, flashing
Holiday mode
orange, continuous
Defects
agenta, flashing/continuous
Содержание RED 30 320
